User manual SHARP MD-R3

[. . . ] MD/CD DECK OPERATION MANUAL MODEL MD-R3 Thank you for purchasing this SHARP product. For the best performance, read this manual carefully. It will guide you in operating your SHARP product. FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located on the rear of the unit. Model number ___________________________ Serial number ___________________________ Date of purchase ________________________ Place of purchase ________________________ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead s y mb o l , w it h i n a n e q u i la t e ra l triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTI ON: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NO T REM O VE CO VER (OR BACK). [. . . ] Press the INPUT SELECT button until "ANALOG" appears. Adjust the recording level using the REC LEVEL control. MIN MAX q The unit will enter the recording stand-by mode. MIC 5 6 q Adjust the recording level so that the maximum level does not exceed "0 dB". Press the MD 06 button. q Recording will start. To interrupt a recording: ENTER RECORD Press the MD button while recording. q The unit will enter the recording stand-by mode. q To resume recording, press the MD button again. q The track number will increase by one each time you interrupt a recording. 06 06 To stop recording: Press the MD s button. s To re-record When you want to re-record a track, erase the previously recorded track and start a new recording, or start recording from any point within the old track. If you start recording from within a track, all of the tracks and track names that follow will be erased. If you want to erase all of the tracks and re-record the disc, you can erase all of the tracks using the all erase function. Then you simply perform the normal recording operations. (Page 30) REC MD 1 1 12 4 0dB OVER During playback, press the MD you want to begin re-recording. 06 button at the point where 4567 8 9 10 11 12 13 14 15 16 17 18 q The unit will pause. (When recording starting from 3 minutes and 32 seconds into the fourth track) 2 3 Press the RECORD (REC) button. Select the recording source and start recording. q To cancel the operation, press the MD s button. 2 4567 8 9 10 11 12 13 14 15 16 17 18 q The unit will be in the recording pause mode. 3 4 TOC 12 4 0dB OVER 12345 4 TOC 12 4 0dB OVER 12345 23 MD-R3 (Continued) RECORD s To create your own track numbers while recording By creating your own track numbers while recording, you can mark them and later search for any passage you wish. (You can also create your own track numbers during digital recording. ) Press the RECORD (REC) button during recording at the point where you want to create a track number. q After the track number has been written on the disc, the recording will continue. REC Note: q If you use the MD editing function, the recorded track numbers can be changed, and the space between tracks can be changed. (Page 25) 12 4 0dB OVER 12345 q The track number increases by one. s Recording tracks as a single track (Remote control operation) When making an analog recording, you can record several pieces of music as a single track, without using the auto marker function. AUTO MARK 1 2 Press the AUTO MARK button on the remote control while the recording is paused. q "A. MARK OFF" will appear. Press the MD 06 button. q This unit will start recording. Note: q When making digital recordings using a CD player or an MD player, track numbers will be created automatically regardless of the setting of the auto marker function. 1 "A. MARK OFF" will appear. s To cancel the selection currently being re4 0dB OVER 12 corded (Rec cancel) While making the following recordings, you can erase any tracks you don't want to record. q While making a sound synchro recording q While making a normal recording from an external unit, using the auto marker function q While making a recording from a CD without using the track edit or one-touch edit function Press the REC CANCEL button while recording. q The selection currently being recorded will be erased from the MD and the unit will enter the normal recording stand-by mode. (The playback on the other unit will not stop. ) q While a track is being erased, the sound from the other unit will not be heard. 1 SYNC REC REC CANCEL To resume recording: Press the MD button. q To resume sound synchro recording, press the SYNC REC button. Note: q The track currently being recorded cannot be canceled while you are making an APMS or random recording from a CD. 06 24 MD-R3 EDITING We will explain the 5 editing features you can use to create your own original MiniDiscs. Playback-only MiniDiscs cannot be edited. DIVIDE A track can be divided into two tracks. [. . . ] at 1 kHz: OPTICAL Square IN (Optical) optical connector COAXIAL (Coaxial) Pin jack 75 ohms 600 ohms 500 mVp-p 6 mVrms MIC (Micro- Stereo phone) jack q Compact disc player Type: Signal readout: 3-disc multi-play compact disc player Non-contact, 3-beam semiconductor laser pickup 200 - 500 rpm CLV, Approx. CIRC (Cross Interleave Reed-Solomon Code) 16-bit linear 4 - 20, 000 Hz (+0/­1 dB) 1 bit 100 dB (1 kHz) 90 dB (1 kHz) Unmeasurable (less than 0. 001% W. peak) Output jacks Jack name Jack shape Output Load level impedance 15 mW 2 Vrms 32 ohms 50 kohms Rotation speed: Error correction: Quantization: Frequency response: D/A converter: Signal/noise ratio: Dynamic range: Wow and flutter: PHONES 1/4" (6. 3 mm) stereo (Headphones) jack LINE OUT Pin jack OPTICAL Square optical connector OUT (Optical) q Timer/clock Type: Timer: Digital clock with date function ON/OFF, once a day 44 MD-R3 MEMO MD-R3 MEMO MD-R3 LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction. [. . . ]