User manual SHARP MD-X8

[. . . ] MD/CD STEREO MODEL MD-X8 OPERATION MANUAL Thank you for purchasing this SHARP product. For the best performance, read this manual carefully. It will guide you in operating your SHARP product. MD-X8 MD/CD stereo consisting of MD-X8 MD/CD stereo CP-X8 2 way speaker system. CONTENTS Page IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In such a case, restart the recording again, or add the disc and track names using the DISC NAME function and the TRACK NAME function, after you are through recording. (Page 36) 30 *27-37 30 98. 6. 23, 10:32 AM EDITING We will explain the 5 editing functions you can use to create your own recorded MiniDiscs. Divide 1 2 3 A 1 2 B 3 C D 4 A B C D A track can be divided into two tracks. If two selections were recorded as a single track because there was not enough silent space between the tracks, you can use the DIVIDE function to separate the selections. This feature is also convenient for identifying specific points with one selection so that you can locate those points easily whenever you like. (Page 33) 1 2 3 4 Combine Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silence in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 33) A 1 2 B 3 C C A B C Erase 1 2 3 4 5 A 1 2 B C 3 4 D E Tracks you want to erase can be erased one at a time or all at once. Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. (Page 35) A B D E Move The order of the recorded tracks can be changed. This feature is different from program play. A new track order can be recorded directly on the disc. When the power is turned off, the revised order will not be changed. (Page 34) 1 2 3 4 A 1 2 B 3 C D 4 C A B D Program move function This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. The track numbers will be adjusted as needed, automatically. (The tracks that are not included in the programmed selections will be put at the end of the new track number sequence. ) (Page 34) 1 2 3 4 A 1 2 B 3 C D 4 C A D B Track/Disc name M DWWW 1 2 WWW 5 5 : 0 8 W T O T A L B E S T WH I T S WWWWWWWWWWWW WWW 1 W L O V E W S O N GWWWWWWW WWW 2 WWA V E WWWWWWWWWWWW WWW 3 W F O RW E V E RWWWWWWWW You can assign titles to recorded tracks and to discs. The characters must be capital and lowercase letters, or symbols. Track and disc names can use up to 100 characters per name. (Page 36) 31 *27-37 31 98. 6. 23, 10:32 AM (Continued) H Using the editing function We will show you some examples of how to use the editing functions. You can create a disc of your favorite selections by recording tracks from a variety of input sources such as CDs and radio broadcasts. STEP 1 Recording tracks to be edited on an MD Digital recording from a CD Recording an AM broadcast Recording an FM broadcast A B C D D Talk E Live performance STEP 2 Putting the space between tracks in order A B C D D Talk E Live performance The tracks are combined using the combine function. The tracks are divided using the divide function. D Talk E F G CM H STEP 3 Cutting unnecessary sections A B C Cut using the erase function. Cut using the erase function. [. . . ] CIRC (Cross Interleave Reed-Solomon Code) 16-bit linear 1-bit 4-times oversampling digital filter 20 - 20, 000 Hz (+1/-3 dB) 95 dB (1 kHz) 90 dB (1 kHz) Unmeasurable (less than 0. 001% W. peak) H Speaker section Type: Maximum input power: Rated input power: Impedance: Dimensions: Weight: 2-way 6" (150 mm) woofer and 1" (25 mm) dome tweeter type 100 W 50 W 6 ohms Width; 7-13/16" (197 mm) Height; 11-3/4"(297 mm) Depth; 11-1/16"(281 mm) 9. 7lbs. (4. 4 kg)/each (Tuner section) Frequency range: Sensitivity: FM; 87. 5 - 108 MHz AM; 530 - 1, 720 kHz FM; 2. 5 µV (75 ohms, unbalanced) AM; 650 µV/m 57 38-58 57 98. 6. 23, 10:34 AM 58 38-58 58 98. 6. 23, 10:34 AM CALLING FOR SERVICE For location of the nearest Sharp Authorized Service Center, or to obtain product literature, accessories, supplies or customer assistance, please call 1-800-BE SHARP. LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction. [. . . ]