User manual SHARP MD-ZV30

[. . . ] S M <P=001> S M <P=001> S M <P=001> S M <P=001> MD STUDIO MD STUDIO MD STUDIO MD STUDIO MODEL MODELL MODÈLE MODELO MD-ZV30H OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO MD-ZV30H TINSZ0217AWZZ ESPAÑOL FRANÇAIS DEUTSCH ENGLISH SM <P=001> SPECIAL NOTES FOR UK CUSTOMERS ONLY NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. [. . . ] Be aware that when you do this, all of the tracks and track names that follow the newly recorded track will be erased. 1 2 3 4 Press the CD s button. Load a compact disc and a recordable MiniDisc. Press the CD button. 1 2 3 4 During playback, press the MD 0 you want to begin re-recording. Press the ENTER button. 6 button at the point where q The unit will pause. q This unit will be in the recording pause mode. q To cancel the operation, press the MD s button. Select the recording source and start recording. q The unit will enter the record stand-by mode. 06 To stop recording: Press the MD s button. q After the track number has been written on the MiniDisc, the recording will stop. However, CD playback will continue. E-22 MD-ZV30H TINSZ0217AWZZ <P=003> EDITING We will explain the 5 editing functions with which you can create your own original discs from recorded MiniDiscs. Playback-only MiniDiscs cannot be edited. DIVIDE A track can be divided into two tracks. If two selections were recorded as a single track because there was not enough silent space between the pieces, you can use the DIVIDE function to separate the selections. This feature is also convenient for identifying specific points with one selection so that you can locate those points easily whenever you like. (Page 24) 1 2 3 MOVE The order of the recorded tracks can be changed. This feature is different from programme play. A new track order can be recorded directly on the disc. When the power is turned off, the revised order will not be changed. (Page 26) 1 2 3 4 A 1 2 B 3 C D 4 1 A 2 B 3 C 4 D A B C D C A B D COMBINE Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silent section in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 25) 1 2 3 4 Programmed move This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. The track numbers will be adjusted as needed, automatically. (The tracks that are not included in the programmed selections will be put at the end of the new track numbers. ) (Page 26) 1 2 3 4 A 1 B 2 3 C D A 1 B 2 C 3 D 4 A B C D C A D B ERASE Tracks you want to erase can be erased one at a time or all at once. [. . . ] q Contact the shop where you purchased the unit. q Unplug the AC power lead, plug it back, and then turn the power on. q Erase all of the tracks, and try recording. q The TOC information could not be created properly q Turn off the power, and try to write the TOC again. due to a mechanical shock or to scratches on the (Remove any source of shock or vibration whilst disc. [. . . ]