User manual SHARP MD-X3H OPERATION MANUAL

[. . . ] 54 ACCESSORIES FM aerial × 1 AM loop aerial × 1 Remote control × 1 "AA" size battery (UM/SUM-3, R6, HP-7 or similar) × 2 Note: Parts and accessories mentioned in this operation manual other than those in the drawing are not included. MD-X3HH(SUK) TINSE0227AWZZ YO <P=001> SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. [. . . ] (pages 12 - 13. ) Load a recordable MiniDisc. Check the recording mode by pressing the REC MODE button. Press the MD q REC button. 25 3 5 To record the track number whilst recording: The recording is performed as a single track. To identify different sections of a recording you can increase the track number at any point during the recording process. To create a new track number, whilst in the recording mode, press the MD q REC button. q The track number will increase by one, and then the recording will continue. q The unit will enter the recording stand-by mode. At this time, auto tuning is impossible. Note: q Before recording an AM broadcast, enter the recording stand-by mode, and then separate the AM loop aerial from the main unit. Adjust it so that the AM broadcast can be tuned in most clearly. 5 6 Check the recordable time by pressing the DISPLAY button. Press the MD 0 6 button. q During recording, you cannot change the station. To stop recording: Press the MD s button. After the track number has been written on the MiniDisc, the recording will stop. To interrupt recording: Press the MD Press the MD crease. 06 06 button whilst recording. Press the MD button. 3 4 q The unit will enter the recording stand-by mode. 06 q Recording will begin. 2 3 30 MD-X3HH(SUK) TINSE0227AWZZ <P=002> (Continued) s Recording from a CD or an MD to a cassette tape (One-Touch Editing) CD CD MD MD CD TAPE MD TAPE TAPE TAPE A CD or an MD can be recorded, starting from the first track, with a one-touch operation. 1 2 3 4 Load a blank cassette into the cassette compartment. Select the Dolby NR mode by pressing the DOLBY NR button. q Wind past the tape leader which cannot be recorded on. DOLBY NR REVERSE MODE q When recording with the Dolby NR system, turn on the indicator. q When not recording with the Dolby NR system, turn off the indicator. Recording from a CD: Press the CD MD TAPE DOLBY NR MD CD CD REVERSE MODE GG 0 TAPE button. 0 TAPE button. Recording from a MiniDisc: Press the MD To stop recording: Press the CD s (MD s) or TAPE s button. 2 s Recording from a CD or an MD to a cassette tape (Synchronised Recording System) When a CD or an MD is played, recording will start automatically. 1 2 3 3 4 5 Load a blank cassette into the cassette compartment. Select the Dolby NR mode by pressing the DOLBY NR button. q Wind past the tape leader which cannot be recorded on. q When recording with the Dolby NR system, turn on the indicator. q When not recording with the Dolby NR system, turn off the indicator. Press the TAPE q 6 button. GG q The unit will enter the recording stand-by mode. Recording from a CD: Press the CD 06 button. Recording from a MiniDisc: Press the MD 06 button. To interrupt recording: Press the CD 0 Press the CD 0 6 6 (MD (MD 0 6) 0 6) button. button again to resume recording. To stop recording: 1 2 Press the CD s (MD s) button, whilst recording. Press the TAPE s button. q The CD or MD will stop, and the unit will enter the stand-by mode. [. . . ] q Unplug the AC power lead, plug it back, and then turn the power on. q Erase all of the track, and try recording. q Set this unit to the stand-by mode and try to write the TOC again. (Remove any source of shock or vibration whilst writing. ) q Replace it with another disc. [. . . ]