User manual SHARP NOTEVISION XR-10S OPERATION MANUAL

[. . . ] Introduction MULTIMEDIA PROJECTOR MODEL Quick Start PG-MB66X/PG-MB56X XG-MB50X-L XR-11XC-L XR-10X-L/XR-10S-L OPERATION MANUAL Setup Connections Basic Operation Useful Features Appendix IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10. Model No. : Serial No. : Before using the projector, please read this operation manual carefully. Introduction Introduction 1. WARRANTY ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. [. . . ] *2 Items when inputting component signal through INPUT 1 or INPUT 2, or when selecting INPUT 3 or INPUT 4. *3 Adjustment range for PG-MB66X/PG-MB56X/XG-MB50X-L/ XR-11XC-L/XR-10X-L. *5 An item which appears in the menu when using PG-MB66X or PG-MB56X. *6 "Tone" will appear on the menu screen only when PAL or SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust "Tone", but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals. Page 42 Background Useful Features Page 42 Setup Guide [On/Off] Logo Blue None Page 42 PRJ Mode Page 42 Language Front Ceiling + Front Rear Ceiling + Rear English Deutsch Español Nederlands Français Italiano Svenska Português Page 42 35 Menu Items (Continued) "Projector adjustment (PRJ-ADJ)" menu Main menu Picture Auto Search Auto Sync Auto Power Off System Sound Speaker RS-232C Fan Mode System Lock Lamp Timer(Life) SEL. /ADJ. SCR - ADJ PRJ - ADJ On On On On On 9600 bps Normal Help PRJ - ADJ Auto Search [On/Off] Sub menu Page 43 Page 43 Auto Sync [On/Off] Page 43 Auto Power Off [On/Off] Page 43 System Sound [On/Off] 0h ENTER 100% END Page 43 Speaker [On/Off] Page 43 RS-232C Page 44 Fan Mode 9600 bps 115200 bps Normal High Old Code New Code Reconfirm Page 44 System Lock Page 44 Lamp Timer(Life) Page 44 "Help" menu Picture SCR - ADJ PRJ - ADJ Help The items you can set with the "Help" menu "Help" menu n Page 46 · Vertical stripes or flickering image appear Auto Sync Adjust vertical noise Adjust horizontal noise · Data image is not centered Auto Sync H-Pos V-Pos · Color is faded or poor INPUT 1 or INPUT 2 Signal type: Auto/RGB/Component INPUT 3 or INPUT 4 Video System: A u t o / P A L / S E C A M / NTSC3. 58/NTSC4. 43/PALM/PAL-N/PAL-60 * The selectable items vary depending on the input signal and the selected input mode. There is no picture or audio Vertical stripes or flickering image appear Data image is not centered Color is faded or poor Picture is dark The image is distorted Reset all adjustments to default settings SEL. ENTER END 36 Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button RETURN button · Press l RETURN to return to the previous screen when the menu is displayed. Menu Selections (Adjustments) Example: Adjusting "Bright". · This operation can also be performed by using the buttons on the projector. 1 2 Press BMENU. · The "Picture" menu screen for the selected input mode is displayed. Example: "Picture" screen menu for INPUT 1 (RGB) mode Menu item Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 7500K 1 Bright PRJ - ADJ Standard Help Press Q or O and select "Picture" to adjust. Useful Features ENTER END 37 Using the Menu Screen (Continued) 3 Press P or R and select "Bright" to adjust. · The selected item is highlighted. Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 7500K 1 Bright PRJ - ADJ Standard Help Single ADJ END Items to be adjusted Picture Resize Image Shift Keystone Auto Keystone SCR - ADJ 0 0 Off PRJ - ADJ Normal Help To adjust the projected image while watching it Press hENTER. · The selected item (e. g. "Bright") is displayed by itself at the bottom of the screen. · When pressing P or R, the following item ("Red" after "Bright") will be displayed. The item displayed by itself Picture Bright SEL. /ADJ. Menu END Note · Press hENTER again to return to the previous screen. 4 Press O or Q to adjust the item selected. · The adjustment is stored. Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 15 0 0 7500K 1 PRJ - ADJ Standard Help Bright Single ADJ END 5 Press BMENU/HELP. · The menu screen will disappear. Note · Menu buttons do not function while the projector is operating the "Auto Sync", "Break Time", "FREEZE", or "AV MUTE" functions. 38 Picture Adjustment ("Picture" menu) Menu operation n Page 37 Q Example: "Picture" screen menu for INPUT 1 (RGB) mode Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 7500K 1 Bright PRJ - ADJ Standard Help Q Example: "Picture" screen menu for INPUT 3 mode Picture Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 0 7500K 1 3D Progressive Bright ENTER END PRJ - ADJ Standard Help ENTER END 1 Selecting the Picture Mode Selectable items Standard The default settings of each item when selecting Picture Mode Description CLR Temp For standard image 7500K 7500K 6500K 7500K ­ Bright Boost 1 2 0 2 ­ Lamp Setting Bright Bright Eco + Quiet Bright Bright Presentation Brightens portions of image for more enhanced presentations. Movie Game *sRGB Gives natural tint to the projected image. For high fidelity reproduction of images from a computer. · "sRGB" is displayed only when RGB signal is input. · You can set or adjust each item in the "Picture" menu to your preference. Any changes you make are retained in memory. Note · You can also press G PICTURE MODE on the remote control to select the picture mode. (See page 34. ) · *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when "sRGB" is selected. For additional information about the sRGB function, visit "http://www. srgb. com/". You cannot set the items, "Red", "Blue", "CLR Temp", "Bright Boost", when "sRGB" is selected. Useful Features Info · When "sRGB" is selected, the projected image may become dark, but this does not indicate a malfunction. 39 Picture Adjustment ("Picture" menu) (Continued) Menu operation n Page 37 2 Adjusting the Image Adjustment Items Contrast Bright Red*1 Blue*1 Color*2 Tint*2 *3 Sharp*2 Bright Boost*1 O button For less contrast. [. . . ] 15 Replacing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52, 53 Resize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 41 RESIZE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 RETURN button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]