User manual SHARP UP-600/700

[. . . ] POS TERMINAL MODEL UP-600 UP-700 INTER-REGISTER COMMUNICATION SYSTEM INSTRUCTION MANUAL TABLE OF CONTENTS Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Inline Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Message display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 (1) The message displayed during inline communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] check Key capture report Hourly report X1 X1 X1 X2/Z2 Job # 110 210 112 212 113 213 119 219 130 230 133 233 139 179 160 Use the military time (24-hour) system. For example, to set 2:30 a. m. , enter 230; and to set 2:30 p. m. , enter 1430. For all 48 half-hours with zero skipped Group no. (0 thru 9) Required data/Remarks DEPT. TRANSACTION X1, Z1 DAILY NET GLU Daily net report GLU report X1, Z1 X2, Z2 160 270 180 GLU/PBLU code. (The range can be specified by entering start and end codes. ) GLU BY SERVER CLOSED GLU GLU report by server Closed GLU report X1, Z1 X1, Z1 181 182 Bill no. (The range can be specified by entering start and end codes. ) CL-GLU BY SERVER Closed GLU report by server X1, Z1 X1, Z1 183 190 191 X2, Z2 290 291 Stacked report 1 Stacked report 2 Stacked report 1 Stacked report 2 STACKED REPORT Stacked report (X1/Z1) STACKED REPORT Stacked report (X2/Z2) 24 5. Server report At the master, you can generate consolidated transaction reports on all servers or individual servers by performing the reading or resetting operation. At each satellite, you can generate consolidated transaction reports on individual servers by performing the reading or resetting operation. If a specific server is signed on at a machine when resetting operation for a consolidated individual server report is executed at the machine, the data on transactions being handled by the server is also added and printed out. If that server is signed on at another machine, the message "IS SIGNED ON" is displayed, thus the resetting operation for that server cannot be made. Full server report sample In the case of the UP-700: Date Machine no. Time Server name and code Job code Report mode Report type Reset counter Server name Data on server #0001 Server code Data on server #0002 signed on at machine no. 000002 25 3 IRC Programming 1. Setting the machine numbers -- master and satellite It is necessary to insure that each terminal has an assigned machine number to the master and satellites prior to further IRC programming. 1. Turn the mode switch to the PGM2 position. Select "SETTING" and press the [ENTER] key. 3. Select "TERMINAL" and press the [ENTER] key. Select "MACHINE#" from the TERMINAL menu and press the [ENTER] key. 4. Enter a machine number and press the [ENTER] key. Machine number: up to 6 digits (0 - 999999) 5. Repeat steps 1 to 4 for all machines in the IRC system. NOTE In an IRC network, each machine number should be unique. Do not use the same machine number for more than one machine. 26 2. Setting the terminal numbers (IRC machine numbers) -- master and satellite It is assumed that your terminal's setting for inline operations has been performed. 1. Turn the mode switch to the PGM2 position. [. . . ] Clearing procedure After selecting "DATA CLEAR" from the PGM2 mode menu with the same procedure as steps 1 and 2 in "(1) Data clearing of the T-LOG buffer, " select "DAILY NET. " 55 (6) Data clearing of the server sign-on state -- master You can clear the master's server sign-on status flags in case of trouble. This operation is effective only for the sign-on flag for servers who have remained signed on at the master. Clearing procedure After selecting "DATA CLEAR" from the PGM2 mode menu with the same procedure as steps 1 and 2 in "(1) Data clearing of the T-LOG buffer, " select "SIGN ON FLAG. " NOTE The server sales data for each server who has signed on is not collected when the manual clearing of the sign-on state is performed. Server sales data is collected only when the sign-off operation is done correctly at the satellites. (7) Data clearing of the GLU/PBLU data in use -- master You can clear the GLU/PBLU data in use at the master in the event some trouble has occurred. [. . . ]