User manual SHARP UX-BD80/BD90

[. . . ] MODEL UX-BD80/UX-BD90 FACSIMILE OPERATION MANUAL 1. Troubleshooting IMPORTANT PLEASE KEEP THE EXTERNAL & INTERNAL PACKAGING SAFE. PLEASE DO NOT THROW IT AWAY. IN THE UNLIKELY EVENT OF A HARDWARE FAILURE, OUR REPAIR CENTRE WILL ASK YOU TO PUT YOUR SHARP FACSIMILE IN THIS BOX. THANK YOU FOR YOUR ASSISTANCE. MAINS PLUG WIRING INSTRUCTIONS This equipment is fitted with a moulded type mains plug which incorporates a detachable fuse cover, under no circumstances should the plug be used without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type observing the wiring code below. DANGER: The fuse from the cut-off plug should be removed and the plug should be disposed of in a safe manner. [. . . ] (Press to turn on the Transfer ON A. M. FAILURE to turn the function off. ) 5 Press to return to the date and time display. 95 4. Answering Machine Transfer Function 6 Each time the machine receives an incoming message, it will call your programmed transfer number. When you answer, you will hear your recorded message telling you that the call is a transfer call. On the dial pad of your phone, enter and , your remote code number (see page 97), . The machine will play back your messages. · You can also perform any of the remote operations described in Remote Operations later in this chapter (see page 97). Note: When you hang up after a transfer call, the machine will not immediately resume normal operation. If you want the machine to accept calls immediately after a transfer call, enter twice before hanging up (if you and to stop want to hang up during message playback, first enter playback, then enter twice). 96 Remote Operations Remote Operations When you are out, you can call the machine from any tone dial telephone and play back your messages using the remote commands. You can also use these commands to change the reception mode and other settings. Remote code number To access the machine to perform remote operations, you must first enter your remote code number. The remote code number has been set to "001" at the factory. If you wish to use a different number, follow these steps: 1 2 3 4 5 Press once and once. Display: A. M. SETTING Press once and twice. REMOTE CODE Press . REMOTE CODE= SELECT 3 DIGITS Press the number keys to enter a 3-digit remote code number. Press START/ MEMORY to store the remote number, and then to return to the date and time display. 97 4. Answering Machine Remote Operations Toll Saver When you call the machine to listen to your messages, it will answer after two rings if it has received at least one message, or after four rings if it has not received any messages. This allows you to save money on telephone charges, particularly if you are calling long distance. If the machine does not answer after two rings, you can simply hang up before it answers, saving yourself the cost of that call. If you do not want to use the Toll Saver function, you can turn it off by following the steps below. In this case, the machine will answer after the number of rings set with the NUMBER OF RINGS setting (see Changing the number of rings on page 127). 1 2 3 4 Press once and once. Display: A. M. SETTING Press once. TOLL SAVER Press once. TOLL SAVER 1=YES, 2=NO The display briefly shows your selection, then: Press to turn on the Toll Saver to turn it off. function, or RECORDING TIME 5 Press to return to the date and time display. 98 Remote Operations Retrieving your messages 1 Call the machine from a tone dial telephone. When your outgoing message begins, press on the telephone. · You will hear a short beep, and the outgoing message will stop. 2 Enter your remote code number and then press . · You will hear a series of beeps equal to the number of messages recorded, or one long beep if four or more messages have been received. The machine will then play back the messages, beeping once at the end of each message. When all messages have been played back, you will hear a long beep. · If no messages have been received, you will hear a short beep. You can either hang up, or perform any of the operations described in the following section, Other remote operations. 3 While the messages are playing, you can do any of the following: · Repeat: To listen to a message a second time, press 2 and telephone before that message ends. To move back to the previous message, press message. on the 2 and during the first 3 seconds of the current · Skip forward: To skip forward to the next message, press 5 and on the telephone. · Stop: To stop playback, press 0 and on the telephone. After this, you can enter any of the commands described in the following section, Other remote operations. 99 4. [. . . ] · TRANSFER FUNCTION Turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . New transfer number . . . . . . . . Record transfer OGM 8 8 8 8 1 2 3 4 # # # # # 3# # # * 91# 92# 90# 93# (Tel. * * · OGM ONLY MODE Turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 # Turn off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]