User manual SHARP UX-300

[. . . ] MODEL UX-300 FACSIMILE OPERATION MANUAL 1. Troubleshooting WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] will also appear in the NOTE column of the Transaction Report if it has been set to print out. 78 Blocking Reception of Unwanted Faxes Blocking Reception of Unwanted Faxes The Anti Junk Fax function allows you to block reception of faxes from parties which you specify. This saves paper by not printing out unwanted "junk" faxes. To use this function, first turn it on by setting Option Setting 13 to YES as explained in Chapter 8, and then enter the fax numbers from which you do not want to receive faxes as shown below. If you are using the Caller ID function, you can also enter voice numbers. Comments: · Up to 5 numbers can be entered in the Anti Junk Number List. · The Anti Junk function will not operate for a number which has also been stored as a Priority Call number. · To clear a number from the Anti Junk Number List, you need to know the 1-digit number which identifies it. If you have forgotten this number, print out the Anti Junk Number List as explained in Chapter 9. 1 Press the keys shown at right. STORE JUNK # will appear in the display. Press 1 to store a number in the Anti Junk Number List, or 2 to clear a number from the list. FUNCTION 3 2 SET CLEAR or 1 2 3 Storing: Enter a 1-digit number from 1 to 5. This number identifies the fax/voice number you will store in the next step. Clearing: Enter the number which identifies the fax/voice number you want to clear, and go to Step 5. 1 (Example) 79 7. Special Functions Blocking Reception of Unwanted Faxes 4 Enter the full number you want to block (max. of 20 digits). 5 5 5 1 2 3 4 (Example) 5 Press the START/MEMORY key. START/MEMORY 6 Return to Step 3 to enter (or clear) another number, or press STOP to exit. STOP Step 3 or 80 Sending Documents From Memory Sending Documents From Memory With this function, the original document is scanned immediately, stored in memory, and then transmitted once the connection to the receiving machine is made. This is convenient when transmitting to places where the line is often busy, as it saves you from waiting to pick up the original document and frees the feeder for other operations. After transmission, the document will be cleared from memory. Only one memory transmission can be set at a time. The amount of memory currently occupied appears as a percentage in the display while the document is being scanned. 1 Load the document(s). The display will show: READY TO SEND · Set the resolution and/or contrast if RESOLUTION desired. 2 START/MEMORY The display will show: ENTER STATION # 81 7. Special Functions Press the START/MEMORY key and then 1. 1 Sending Documents From Memory 3 Enter the number of the receiving machine using one of the following methods: · Press a Rapid Key. · Press the SPEED DIAL key and 01 02 03 (Example) enter a Speed Dial number. · Enter a full telephone number by pressing the number keys. 4 Press the START/MEMORY key if you entered a Speed Dial number or a full number. · The document will be scanned and START/MEMORY stored in memory. Your fax will then dial the receiving machine and transmit the document (redialling will be done automatically if necessary). If the memory becomes full. . . If the memory becomes full while the document is being scanned, MEMORY IS FULL will appear in the display. Press the START/MEMORY key if you want to transmit the pages which have been stored up to that point in memory. The remaining pages will be ejected from the feeder. After transmission, the memory will be cleared and you can transmit the remaining pages. You will also need to transmit the page which was being scanned when the memory filled up. Press the STOP key if you want to cancel the entire transmission. 82 Polling (Requesting a Fax Transmission) Polling (Requesting a Fax Transmission) Polling allows you to call another fax machine and have it send a document (previously loaded in its feeder) to your machine without operator assistance. [. . . ] Other information Reference : IARC (1996) Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-149-261 H. Mermelstein (1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. [. . . ]