User manual SHARP VC-D810S

[. . . ] Please refer to the relevant laws in your Country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (UK) Limited. THIS MANUAL COVERS A RANGE OF MODELS. ALL OF THE FEATURES MENTIONED MAY NOT NECESSARILY APPLY TO YOUR VCR. (i) REMOTE CONTROL STANDBY 1. SV/V+/TIMER OPERATE INPUT SELECT TIMER ON/OFF MENU SV/V+ /TIMER AUDIO OUT TV CH VOL + 14. [. . . ] If in TIMER STANDBY mode, press TIMER ON/OFF to exit. 2. Press SET to confirm · All the delayed recordings in the VCR's memory will be shown. · SET : SE L ECT : ENT ER ME NU : E X I T You can check the settings and change or cancel them. CHANGING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 2. If you wish to change a delayed recording, press [K/L] to highlight the recording, then press SET. 3. Press [H/J] to highlight the setting to be changed and correct it by using the[K/L] or the NUMBER BUTTONS. 4. When all corrections are complete press SET, then press MENU. CANCELLING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 2. If you wish to cancel a delayed recording, press [K/L] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- 3. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER STAND-BY mode. GB-13 ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. REPEAT will appear on the on-screen display when selected. Press MENU to display the main menu on the screen. MODE MENU SCREEN B L U E MU T E R E P E A T AU T O ON OF F OF F 2. Press MENU to return to normal screen. GB-16 SET : SE L ECT : ENT ER : CHANGE ME NU : E X I T ADVANCED OPERATION LCD DISPLAY TIME OF DAY Shows current time of day, if the clock is set. Press the DISPLAY button until the time of day appears. For example, 21:20 appears: CHANNEL STATUS Shows the current VCR channel preset. Press the DISPLAY button until the channel number appears, for example: TAPE COUNTER AND ZERO BACK Tape counter measures the current position of the video tape in real time. ZERO BACK uses the tape counter to determine a specific point on a tape you may wish to return to. 1. Press the DISPLAY button until tape counter appears, for example: 2. To identify the current position on a video tape press the CLEAR button and the tape counter will appear: When you wish to return to this position on the video tape, press ZERO BACK. The tape will rewind/advance to this point. NOTE: · The tape counter will only operate on recorded sections of tape. DISPLAY BRIGHTNESS The LCD display brightness can be changed to suit the ambient lighting in the room. Switch on the VCR (ensure the menu screen is not on) then press and hold the DISPLAY button for approximately 2 seconds. [. . . ] Not possible to view picture or playback through RF-OUT. · The channel position has been set to be skipped. · Make sure all the cables are connected properly. · Make sure the VCR power cord is properly plugged in. [. . . ]