User manual SHARP VC-MH761SM

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. ® and PlusCode ® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. TIMER ON/OFF 5. AUDIO OUT (This button has no function with these models. ) OPERATE INPUT SELECT TIMER ON/OFF MENU AUDIO OUT CH VOL + 15. TV VOLUME + CH SKIP SEARCH VOL ZERO BACK SET / 17. PLUSCODE PLUSCODE CLEAR MODE OSD 1 4 7 AM/PM 2 5 8 0 3 DISPLAY 6 9 INPUT SELECT CHANNEL / 8. [. . . ] Press SET again, the on-screen display will now show today's date. If you wish to change the date use the [ / ] or the NUMBER BUTTONS. Enter two digits for the day, then two for the month. For example for July 9th, press 0 9 (9th), then 0 7 (July). When the correct date for your recording is shown, press the menu select button to move to the next setting. SET : SE L ECT : ENT ER ME NU : E X I T 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 5. If you want to make additional recordings at the same time each day or week, use [ / ] to select D (daily) or W (weekly). Then press to move to the next setting. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-SP ---- 6. Enter the channel number using the [ / ] or the NUMBER BUTTONS. For example to record a programme on channel 3, press 0 3. Then press to move to the next setting. If problems persist contact the SHARP Helpline on tel: 0990-274277 15 BASIC OPERATION HOW TO SET A DELAYED RECORDING 7. Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP SP --- NUMBER BUTTONS, hours first then minutes (when entering less than 10 hours or minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. If problems persist contact the SHARP Helpline on tel: 0990-274277 17 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape: Pr in long play 2 hour 46 minutes is left on the tape: Pr NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. REPEAT will appear on the on-screen display when selected. [. . . ] The guarantee does not cover carriage costs, batteries or video tapes. In the unlikely event of this product requiring repair, please contact the supplier from whom it was purchased. Where this is not possible, please contact the SHARP Helpline on the telephone number given below. 6. This guarantee is offered as an additional benefit to your statutory rights and does not affect these rights in any way. 7. [. . . ]