User manual SHARP VCMH67HM OPERATION MANUAL

[. . . ] Please refer to the relevant laws in your country. No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (UK) Ltd. ® and Pluscode® are registered trademarks of Gemstar Development q q q Corporation. q The Corporation. system is manufactured under license from Gemstar Development THIS MANUAL COVERS A RANGE OF MODELS. ALL OF THE FEATURES MENTIONED MAY NOT NECESSARILY APPLY TO YOUR VCR. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) 712LM cover 14/5/99 12:05 pm Page 3 VCR REMOTE CONTROL STANDBY TV 1. [. . . ] 12-hour clock am/pm can be selected using the AM/PM · · If button on the remote control. appears on the VCR display, press TIMER ON/OFF before starting. Check that the clock is displaying the correct time. SETTING A RECORDING For example: Recording a programme on channel 3 from 21:05 to 22:30 on July 9th. 1. Press SET to confirm. MENU SCREEN 4. The position which is initially highlighted is the next available timer record entry. · The display will automatically show today's date. Either: If this is the date you wish to make the recording on, press SET to confirm this. Or: enter the recording date using the[ / ] or the NUMBER BUTTONS. Enter two digits for the day, then two for the month. For example for July 9th, press 0 9 (9th), then 0 7 (July). T I ME R MOD E SE T UP SET : SE L ECT : ENT ER ME NU : E X I T 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 5. If you want to make additional recordings at the same time each day or week, use [ / ] or select D (daily) or W (weekly). Then press SET to confirm. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-SP ---- 7. When all corrections are complete press SET, then press MENU. CANCELLING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 2. If you wish to cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- 3. Press MENU. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER STAND-BY mode. If problems persist contact the SHARP Customer Helpline on tel: 0990-274277 GB-17 712. book Page 18 Friday, May 14, 1999 12:08 PM ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND (HIFI VCR'S ONLY) Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · · · · Press AUDIO OUT once. The LEFT audio channel will be sent to BOTH speakers. The RIGHT audio channel will be sent to BOTH speakers. The MONO track will be sent to BOTH speakers. L and R will disappear from the VCR display. [. . . ] Press and hold MENU and CHANNEL for 10 seconds. buttons together on the front of the VCR 3. The AUTO INSTALLATION screen should now be showing on your TV. Follow the on-screen display to proceed with auto installation. Refer to the CUSTOMISED INSTALLATION chapter if · · · Your VCR could not tune automatically - due to for example poor reception. [. . . ]