User manual SHARP XL-HP505

[. . . ] Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MICRO COMPONENT SYSTEM MODEL XL-HP505 Micro Component System consisting of XL-HP505 (main unit) and CP-HP505 (speaker system). XL-HP505 OPERATION MANUAL Accessories Please confirm that the following accessories are included. Remote control 1 AM loop antenna 1 (RRMCG0408AWSA) (QANTL0005AWZZ) FM antenna 1 (92LFANT1746A) Note: Only the above accessories are included. XL-HP505 SPECIAL NOTES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Tuning XL-HP505 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). or ) button to tune in to the desired Notes: " When radio interference occurs, auto scan tuning may stop automatically at that point. " Auto scan tuning will skip weak signal stations. " To stop the auto tuning, press the TUNING button again. !To receive an FM stereo transmission Auto power on function: When you press any of the following buttons, the unit turns on. " TUNER (BAND) button (main unit and remote control): The unit turns on and the "TUNER" function is activated. " / button on the main unit: The unit turns on and playback of the last function starts (CD/TAPE/TUNER/VIDEO). Press the TUNER (BAND) button to display the "ST" indicator. " " " will appear when an FM broadcast is in stereo. " If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. FM stereo mode indicator FM stereo receiving indicator 21 Radio Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. XL-HP505 Listening to the radio (continued) !Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a button. To recall a memorized station Press the PRESET ( or lect the desired station. ) button for less than 0. 5 seconds to se- 1 2 Perform steps 1 - 3 in "Tuning" on page 21. Press the MEMORY/SET (MEMORY) button to enter the preset tuning saving mode. !To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) 1 2 Press the PRESET ( or ) button for more than 0. 5 seconds. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. Press the PRESET ( or ) button again when the desired station is located. 3 Radio Within 30 seconds, press the PRESET ( or ) button to select the preset channel number. [. . . ] Amplifier Output power 75 watts minimum RMS per channel into 6 ohms from 60 Hz to 20 kHz, 10% total harmonic distortion Speakers: 6 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Subwoofer pre-out (audio signal): 200 mV/ 10 k ohms at 70 Hz Video/Auxiliary (audio signal): 500 mV/47 k ohms Type Output terminals Maximum input power Rated input power Impedance Dimensions 2-way type speaker system 2" (5 cm) tweeter 5-1/8" (13 cm) woofer 150 W 75 W 6 ohms Width: 6-1/2" (165 mm) Height: 10-1/4" (261 mm) Depth: 9-11/16" (246 mm) 6. 2 lbs. (2. 8 kg)/each Input terminals Weight !CD player Type Signal readout D/A converter Frequency response Dynamic range 5-disc multi-play compact disc player Non-contact, 3-beam semiconductor laser pickup 1-bit D/A converter 20 - 20, 000 Hz 90 dB (1 kHz) 35 References !Speaker CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. [. . . ]