User manual SHARP XL520E OPERAION MANUAL

[. . . ] Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur. [. . . ] To listen again to the track being played: (Main unit operation) VOLUME /JOG 1 Jog dial Press the VOLUME/JOG button. q The track number will flash. Whilst the track number is flashing, turn the jog dial anti-clockwise. (Remote control operation) Press the 5 3 button for less than 0. 5 seconds during playback. 2 RANDOM/ REPEAT To move to the beginning of the next track: (Main unit operation) 1 2 s Repeat and random play (Remote control operation) Press the VOLUME/JOG button. Whilst the track number is flashing, turn the jog dial clockwise. q The track number will flash. 1 Press the RANDOM/REPEAT button. q Each time this button is pressed, the mode will change in the following order: Repeat play Random play Normal play (Remote control operation) Press the 2 4 button for less than 0. 5 seconds during playback. q To skip a number of tracks at one time, press the 5 3 or 2 4 button on the remote control repeatedly until the desired track number is shown. q To start playing at a desired track, press the 5 3 or 2 4 button on the remote control whilst in the stop mode to select the track number, and then press the 0 / CD 6 (0 6) button. 2 Press the playback. 0 / CD 6 (0 6) button to start s Cue and review To cancel repeat or random play: Press the RANDOM/REPEAT button until "R" or "RANDOM" disappears. 1 2 3 Load a disc and begin playback. Hold the 2 button down for audible fast forward, and hold the 3 button down for audible fast reverse. Normal playback will resume when the 3 button is released. 2 To repeat playback of selected tracks: After entering the programme for the tracks you want to hear using "APMS", select repeat play and start playback. Notes: q When using random play or repeat play, be sure to press the s button after you are through listening. Otherwise, the disc will play continuously. q During APMS operation, random play is not possible. or Notes: q When the end of the disc is reached whilst cueing, the "END" will appear in the display and CD operation is paused. (Metal or CrO2 tape is not recommended. ) For recording, use only normal tape. q Do not use C-120 tapes, tapes with large diameter reels, or poor-quality tapes, as they may cause malfunctions. q Before loading a tape into the cassette compartment, tighten the slack with a pen or pencil. q Cassettes have removable tabs which prevent accidental recording or erasing from taking place. Removing the tab will protect the corresponding side from being erased. Cover the tab holes with adhesive tape to erase or record again. Side A (1) Tab for side B (2) Tab for side A (1) 1 s Tape playback Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "TAPE" appears in the display. Open the cassette door by pushing the area marked "7 PUSH EJECT". Load the cassette into the cassette compartment. Press the 2 3 q Press the TAPE button on the remote control. 1 2 5 4 5 0 button. To stop playback: Press the s button. Fast forward/rewind: To advance the tape, press the s button, then press the button. [. . . ] q If the display is not correct. Commercially available digital cable The CD digital signal from this unit can be recorded by other DAT or MiniDisc recorders. q If the operation is not correct. 1 2 3 4 Remove the DIGITAL OUT socket cover. Use a commercially available digital cable to connect the unit to the OPTICAL IN socket of a MiniDisc recorder or a DAT. Put the external unit in the recording mode. Play a CD on this unit. 1 2 3 Press the ON/STAND-BY button to enter the stand-by mode. [. . . ]