User manual SHARP XLMP100H OPERATION MANUAL

[. . . ] XL-MP100H(E) TINSEA015SJZZ 1 MICRO COMPONENT SYSTEM MODEL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. XL-MP100H Micro Component System consisting of XL-MP100H (main unit) and CP-MP100H (speaker system). XL-MP100H OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/customersupport. [. . . ] If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2. Preset channel Frequency and frequency band " To erase entire preset memory 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. Whilst pressing down the MEMORY/ SET button and the PRESET button, press the ON/STAND-BY button until "TUNER CL" appears. 4 Radio 6 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. Note: The backup function protects the memorised stations for a few hours should there be a power failure or the AC power lead disconnection. 19 04/1/28 XL-MP100H(E)UK2. fm TINSEA015SJZZ XL-MP100H Listening to a cassette tape Before playback: !For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended. ) !Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack with a pen or a pencil. 3 Open the cassette compartment by pushing the area marked "PUSH EJECT ". 4 Load a cassette into the cassette compartment with the side to be played facing toward you. Close the cassette compartment by pushing the area marked "PUSH EJECT ". button to start 5 Tape Playback 6 When playback is performed using the remote control, press the button. Fast forward/rewind: To advance the tape, press the button. To rewind it, press the 1 2 Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "TAPE" appears on the display. When operating with the remote control, press the TAPE button. Caution: !To remove the cassette, press the button, and then open the compartment. Before changing from one tape operation to another, press the button. If a power failure occurs during tape operation, the tape head will remain engaged with the tape and the cassette compartment will not open. In this case, wait until the power is restored. Even if the ( ) button is pressed during tape playback, the unit will not enter the pause mode. 20 04/1/28 XL-MP100H(E)UK2. fm TINSEA015SJZZ Recording on a cassette tape Before recording: !When recording important selections, make a preliminary test to ensure that the desired material is properly recorded. SHARP is not liable for damage or loss of your recording arising from malfunction of this unit. The volume and sound controls can be adjusted with no effect on the recorded signal (Variable Sound Monitor). Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. [. . . ] Cleaning the CD pickup lens Poor performance during CD playback (skipping or jumping) can be caused by a dirty or contaminated CD laser pick up lens. If this happens then the use of a commercially available CD lens cleaning discs may restore normal operation. Contact your supplier or local CD software dealer to obtain CD lens cleaning discs. Ensure all included instructions/documentation are carefully followed. 34 04/1/28 XL-MP100H(E)UK3. fm TINSEA015SJZZ Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]