User manual SHARP XV-Z9000U

[. . . ] Before using the projector, please read this operation manual carefully. ENGLISH Information Important OPERATION MANUAL IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied Accessories" on page 12. ENGLISH Model No. : XV-Z9000U Serial No. : There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT "LIMITED WARRANTY" CLAUSE. [. . . ] Select CUSTOM as your default setting if you prefer a smooth textured image to a sharply contrasted one. · STANDARD and GAMMA 2 settings of VIDEO mode (except COMPONENT 480P/720P/1080i) incorporate a DYNAMIC GAMMA function for optimizing GAMMA correction frame by frame in real time, thus providing a more beautiful image. · GAMMA 1 settings are the same for both RGB and VIDEO modes. CUSTOM E-25 s s Using the GUI (Graphical User Interface) Menu Screen Basic Operations This projector has two sets of menu screens that allow you to adjust the image and various projector settings. These menu screens can be operated from the projector or the remote control with the following procedure. 1, 7 4 6 2, 3, 5 (GUI) On-screen Display INPUT 3, 4 (VIDEO) mode INPUT 1, 2 (COMPONENT) or 5 (RGB) mode 1 2 1 2 Main menu 3 Sub menu 3 Basic Operation 5 5 4 2 1 Press MENU to display the INPUT 1, 2, 3, 4 or 5 mode menu bar. 2 Press / to select an adjustment main menu on the menu bar. 3 Press / to select a specific adjustment item. 5 4 To display a single adjustment item, press ENTER after selecting the item. Only the menu bar and the selected adjustment item will appear. 5 Press / to adjust the item. 6 Press UNDO to return to the previous screen. 7 To exit the GUI, press MENU. · For details on items on the menu screen, see the tree charts on pages 27 and 28. E-26 Menu Bars Items on the INPUT 3 or 4 Mode Menu Bar Main menu Picture Sub menu Contrast Brightness Color Tint Sharp Red Blue CLR Temp Reset Progressive Mode 2D Progressive 3D Progressive Film Mode 30 30 30 30 30 30 30 3 30 30 30 30 30 30 30 3 Main menu PRJ Mode Sub menu Front Ceiling Front Rear Ceiling Rear Language English Deutsch Español Nederlands Français Italiano Svenska Português Options 3D DNR [ON/OFF] Theater Mode [NORMAL/BRIGHT] Lamp Timer OSD Display Normal Level A Level B Video Systems Auto PAL (50/60Hz) SECAM NTSC4. 43 NTSC3. 58 Status Basic Operation PAL­M PAL­N Background Blue None Economy Mode RS-232C Port [ON/OFF] Auto Power Off [ON/OFF] RS-232C 9600bps 38400bps Subtitle 30 30 * 115200bps * These values may be changed using the RESIZE mode. · Only the items highlighted in the tree charts above can be adjusted. · To adjust the items under the sub menu, press after selecting the sub menu. E-27 Menu Bars Items on the INPUT 1, 2 or 5 Mode Menu Bar Main menu Picture Sub menu Contrast Brightness Color Tint Sharp Red Blue CLR Temp Reset Signal Type Progressive Mode 30 30 30 30 30 30 30 3 30 30 30 30 30 30 30 3 RGB Component 2D Progressive 3D Progressive Film Mode 150 60 150 60 1 2 · · Main menu PRJ Mode Sub menu Front Ceiling Front Rear Ceiling Rear Language English Deutsch * Español Nederlands Français Italiano Svenska Fine Sync Clock Phase H-Pos V-Pos Reset Save Setting Select Setting 150 60 150 60 Resolution 800 600 640 480 Vert Freq 75 Hz 72 Hz Português 7 Resolution 800 600 640 480 Vert Freq 75 Hz 72 Hz Status 1 2 · · Special Modes Signal Info Auto Sync Auto Sync Disp [ON/OFF] 7 Resolution 640 480 720 480 1 2 · · 7 Resolution Hor Freq Vert Freq Off Normal High Speed Options 3D DNR [ON/OFF] 640 480 37. 5 kHz 72 Hz Basic Operation * Theater Mode [NORMAL/BRIGHT] Lamp Timer OSD Display Normal Level A Level B Background Blue None Economy Mode RS-232C Port [ON/OFF] Auto Power Off [ON/OFF] RS-232C 9600bps 38400bps Subtitle 30 30 *, ** 115200bps * Not displayed in the INPUT 5 mode. ** These values may be changed using the RESIZE mode. · · · · The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. "Color", "Tint", and "Sharp" appear only when Component is selected in INPUT 1 or 2 mode. Only the items highlighted in the tree charts above can be adjusted. To adjust the items under the sub menu, press after selecting the sub menu. E-28 Adjusting the Picture You can adjust the projector's picture to your preferences with the following picture settings. 2, 3 1, 4 Description of Adjustment Items Selected item Contrast Brightness Color Tint Sharp Red Blue Reset button button For less contrast For more contrast For less brightness For more brightness For less color intensity For more color intensity Skin tones become purplish Skin tones become greenish For less sharpness For more sharpness For weaker red For stronger red For weaker blue For stronger blue All image adjustment items are returned to the factory preset settings. (GUI) On-screen Display e. (VIDEO input in INPUT 3 or 4 mode) 1 · "Color", "Tint" and "Sharp" do not appear for RGB input in INPUT 5 mode. 1 Press MENU. Menu bar and "Picture" menu screen appear. 2 Press / to select a specific adjustment item. 3 Press / to move the mark of the selected adjustment item to the desired setting. 4 To exit the GUI, press MENU. Basic Operation 2 · To reset all adjustment items, select "Reset" on the "Picture" menu screen and press ENTER. · The adjustments can be stored separately in the INPUT 1 to 5 modes. E-29 Adjusting the Picture Adjusting the Color Temperature This function can be used to adjust the color temperature to suit the type of image input to the projector (DVD, video, computer image, TV broadcast, etc. ). This function can be operated using the CLR TEMP buttons on the remote control, as well as the GUI menu screen. 1, 2 Adjusting the Color Temperature with the Remote Control 1 Press CLR TEMP (­/+) on the remote control. [. . . ] 41 ENTER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Exhaust ventilative hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 U UNDO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 V VIDEO INPUT terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]