User manual SHARP XVC20E OPERATION MANUAL

[. . . ] DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. U. S. A. [. . . ] Since Keystone correction digitally corrects the signal, resolution may slightly decrease when it is used. Moir patterns and line distortions may also be visible in detailed images. If you cannot correct trapezoidal distortion with Keystone correction, change the placement position of the projector. Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting. Also read "About Copyrights" on page 37. The display disappears. GEOMETRIC For correcting an image by ADJUSTMENT designating the corner of the projected image. (See page 34. ) H&V KEYSTONE For correcting an image by designating the horizontal or vertical axes. (See page 35. ) 33 Basic Operation Image Projection (Continued) GEOMETRIC ADJUSTMENT R On-screen display Info When adjusting a 4:3-aspect-ratio input signal to a 4:3-aspect-ratio screen, correct the trapezoidal distortion by setting "RESIZE" to "STRETCH" (16:9). Adjust upper left corner GEOMETRIC ADJUSTMENT ADJUST RESET NEXT END 1 2 3 Press c KEYSTONE on the remote control repeatedly until "GEOMETRIC ADJUSTMENT" is displayed. Adjust the focus, size, and projection angle so that the screen edges line up into the blue area. Line up the screen edges into the blue area as closely as possible. Blue area Geometric Adjustment Screen Upper Left Upper Right Press P, R, O or Q to move the position for the upper left of the image. Adjust the screen until the displayed red arrows line up in the upper left. 4 5 Press i ENTER to set the position. The arrow in the upper right turns red. Lower Left Lower Right Repeat the same procedure with the positions for the upper right, lower right and lower left of the image. When you press e RETURN at this point, you will return to the previous screen. If you press e RETURN before adjusting the upper left corner, the Reset Confirmation screen displays. When you confirm the lower left position, the screen adjustments will be set and the "GEOMETRIC ADJUSTMENT" mode will end. Note The placement of the screen and the projector may result in the image aspect ratio becoming slightly distorted. Try "H&V KEYSTONE" when "GEOMETRIC ADJUSTMENT" does not fully correct trapezoidal distortion. 34 H & V KEYSTONE 1 2 Project the image and adjust the focus, image size, and projection angle. RETURN ENTER END Special Modes Page 46 Auto Sync [On/Off] 1035I 1080I The resolution changes depending on the input signal. The "Fine Sync" menu is not available for INPUT 3 or INPUT 4. Main menu Options 1 Page 46 Cur. freq Page 46 Image Shift -24 +24 Sub menu Page 47 Page 47 Overscan H Overscan V -30 -30 +30 +30 "Options1" menu Options 1 Image Shift Overscan H Overscan V Subtitle OSD Display Video System Signal Type HDMI Setting Background Auto Power Off Lamp Timer(Life) SEL. /ADJ. RETURN 0 0 0 0 On Auto Auto Standard Blue On 0h 100% ENTER END INPUT 1 Page 47 Subtitle -30 +30 Page 47 OSD Display [On/Off] Page 48 Video System Page 48 Signal Type *1 Auto PAL SECAM NTSC 4. 43 Auto RGB Component Standard Enhanced Blue None NTSC 3. 58 PAL-M PAL-N PAL-60 Page 48 HDMI Setting *2 Page 48 Background *1 Item that can be set when using INPUT 3 or INPUT 4. *2 Item that can be set when using IINPUT 5 or INPUT 6. Page 48 Auto Power Off [On/Off] Page 49 Lamp Timer(Life) Page 49 Main menu Options2 PRJ Mode Sub menu "Options2" menu Options 2 PRJ Mode RS-232C STANDBY Mode Fan Mode All Reset Language Front 9600 bps Eco Normal English INPUT 1 Page 49 Page 49 RS-232C Front Ceiling + Front Rear Ceiling + Rear 9600bps 115200bps Standard Eco Normal High Page 50 STANDBY Mode Page 50 Fan Mode Page 50 All Reset Page 50 Language Page 50 SEL. /ADJ. RETURN ENTER END English Deutsch Espaol Nederlands Franais Italiano Svenska Portugus 40 Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU button Adjustment buttons (P/R/O/Q) MENU button ENTER button RETURN button Press eRETURN to return to the previous screen when the menu is displayed. Menu Selections (Adjustments) Example: Adjusting "Bright". This operation can also be performed by using the buttons on the projector. 1 2 Press dMENU. The "Picture" menu screen for the selected input mode is displayed. Example: "Picture" screen menu for INPUT 1 mode Selected input mode Menu icons Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 0 0 0 0 0 0 INPUT 1 Press Q or O to select the menu icon to adjust. The selected icon is highlighted. Useful Features Menu icon Menu screen Picture Fine Sync Options1 Options2 Note The "Fine Sync" menu is not available for INPUT 3 or INPUT 4. SEL. /ADJ. RETURN ENTER END 41 Using the Menu Screen (Continued) 3 Press P or R to select the item to adjust. The selected item is highlighted. Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 0 0 0 0 0 0 INPUT 1 SEL. /ADJ. RETURN Single ADJ END Items to be adjusted To adjust the projected image while watching it Press iENTER. The selected item (e. g. "Bright") is displayed by itself at the bottom of the screen. When pressing P or R, the following item ("Color" after "Bright") will be displayed. The item displayed by itself Picture Bright SEL. /ADJ. Menu END INPUT 1 Note Press iENTER again to return to the previous screen. 4 Press O or Q to adjust the item selected. The adjustment is stored. Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 15 0 0 0 0 0 INPUT 1 SEL. /ADJ. RETURN Single ADJ END 5 Press dMENU. The menu screen will disappear. Note The d MENU button does not function while the projector is operating the "Auto Sync" or "FREEZE" functions. 42 Picture Adjustment ("Picture" menu) Menu operation n Page 41 Q PAGE 1 Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 0 0 0 0 0 0 INPUT 1 Q PAGE 2 Picture Picture Mode CLR Temp BrilliantColorTM C. [. . . ] 14 Rear adjustment foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]