User manual SHERWOOD NEWCASTLE R-863

[. . . ] OPERATINGINSTRUCTIONS AUDIO/VIDEO SURROUND RECEIVER R-863 MASTER VOLUME WRA S WIDE RANGE AMPLIFIER STAGE MULTI CONTROL BAND T/P MODE MULTI ROOM REMOTE SENSOR SOURCE DIRECT CINEMA EQ LOCK TUNING/PRESET ROOM2 FEED DYNAMIC RANGE POWER AUDIO INPUT SELECTOR VIDEO TAPE MON. 7. 1CH DIRECT DECODING SURROUND MODE EXTRA SURR. STEREO DIGITAL/ANALOG STANDBY ON/STANDBY 6. 1/7. 1 ON / OFF PHONES SPEAKER CHANNEL SELECTOR TEST TONE TONE MODE VIDEO LABEL MEMO/ENTER ON/OFF OPTICAL IN S-VIDEO VIDEO L - AUDIO - R R-863 AUDIO/VIDEO SURROUND RECEIVER Introduction UNPACKING AND INSTALLATION ENGLISH Congratulations on Your Purchase!Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. [. . . ] However, when DTS or MPEG signals are input in the following decoding modes, the corresponding surround mode will be automatically selected regardless of using the MULTI CONTROL knob or DSP MODE button: * When DTS signals are input in the auto or DTS mode, the corresponding DTS mode will be selected. * When MPEG signals are input in the auto or MPEG mode, MPEG mode will be selected. Notes: When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input flickers, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format. When the 7. 1 CH DIRECT is selected as an input source, the surround mode cannot be selected. When the source direct function is activated, the decoding mode and surround mode cannot be selected. 21 ENGLISH Continued ENGLISH When playing some multi-channel program sources in the Extra Surround 6. 1/7. 1 mode. RPT A DVD EXTRA SURR. TITLE 7. 1 SURR ENTER RPT A TITLE 7. 1 SURR RETURN INTRO B VOL. CH LEVEL CH SEL 6. 1/7. 1 or DISC P. SCAN TEST TONE TUNER CD T1/MON AUX VID1 VID2 VID3 VID4 SYS DISP SLEEP DIRECT IN AUTO DSP MODE ST CENTER MODE PHONO VID5 ROOM2 HOME THEATER MASTER RNC-220 When the digital signals from the following program sources only are input in the available decoding mode, if these buttons are pressed, the corresponding surround mode will be selected. Dolby Digital 5. 1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX technology) : EXTRA SURROUND mode, DTS 5. 1-channel sources : DTS ES MATRIX mode. Press the EXTRA SURROUND 6. 1/7. 1 button on the front panel or the 7. 1 CH SURROUND button on the remote control again to cancel the 6. 1(or 7. 1) surround mode. According to whether the surround back speaker is set to "1CH" or "2CH", the 6. 1 or 7. 1 mode is selected. However, when the surround back speaker is set to "None", the Extra Surround 6. 1/7. 1 mode cannot be activated. When canceling the surround mode for normal stereo operation. DVD STEREO VOL. CH LEVEL CH SEL ENTER RPT A TITLE INTRO B or 7. 1 SURR RETURN AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE ST TUNER CD T1/MON AUX PHONO VID1 VID2 VID3 VID4 VID5 SYS DISP SLEEP DIRECT IN ROOM2 HOME THEATER MASTER RNC-220 Then the stereo mode is selected. To cancel the stereo mode, select the desired surround mode with using the MULTI CONTROL knob or the DSP MODE button, etc. 22 If you have performed the CH LEVEL TRIM procedure on the OSD menu, you can skip this procedure. (For details, refer to "SETTING THE CH LEVEL TRIM" on page 43. ) MULTI CONTROL DVD VOL. CH LEVEL 3 Select the desired channel. or DVD OSD CH SEL CH LEVEL ENTER RPT A TITLE 7. 1 SURR RETURN INTRO B AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE TUNER CD T1/MON AUX PHONO VID1 VID2 VID3 VID4 VID5 CHANNEL SELECTOR VOL. CH LEVEL CH SEL DOWN UP SYS DISP SLEEP DIRECT IN ROOM2 OSD CH SEL HOME THEATER MASTER RNC-220 ENTER RPT A TITLE 7. 1 SURR RETURN INTRO B or DISC P. SCAN TEST TONE TUNER CD T1/MON AUX VID1 VID2 VID3 VID4 SYS DISP SLEEP DIRECT IN AUTO DSP MODE ST CENTER MODE PHONO VID5 ROOM2 HOME THEATER MASTER RNC-220 If the channel display disappears, start from the above step again. Each time this button is pressed, the corresponding channel is selected and displayed for 3 seconds as follows: FRONT-L CENTER(or FRONT-C) FRONT-R SURR-R SUBWOOFER SURR-L (( SURR-C) or ( BACK-L BACK-R)) Depending on the speaker setting, items set to None or No can not be selected. 5 7 Repeat the above steps and to adjust each channel level until the sound level of each speaker is heard to be equally loud. Adjusting each channel level with test tone Only when playing a program source in available At each channel, adjust the level as desired until the sound level of each speaker is heard to be equally loud. surround modes except the DOLBY VIRTUAL mode, the volume level of each channel can be adjusted easily with the test tone function. Note : When the 7. 1 CH DIRECT is selected as an input source, the test tone function does not work. MULTI CONTROL DVD VOL. CH LEVEL OSD CH SEL CH LEVEL ENTER RPT A TITLE 7. 1 SURR RETURN INTRO B or DOWN UP AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE TUNER CD T1/MON AUX PHONO 6 Enter the test tone mode. VID1 VID2 VID3 VID4 VID5 SYS DISP SLEEP DIRECT IN ROOM2 HOME THEATER MASTER RNC-220 DVD TEST TONE VOL. CH LEVEL CH SEL ENTER or RPT A TITLE 7. 1 SURR INTRO B RETURN You can select the desired channel and adjust its level with repeating the steps and in "Adjusting each channel level" procedure. TEST TONE AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE TUNER CD T1/MON AUX PHONO VID1 VID2 VID3 VID4 VID5 SYS DISP SLEEP DIRECT IN ROOM2 HOME THEATER MASTER RNC-220 The test tone will be heard from the speaker of each channel for 2 seconds as follows: Front Left Center Front Right Surround Right Surround Left (( Surround Center) or ( Back Left Back Right)) SUBwoofer Depending on the speaker setting (None or No), the test tone of the corresponding channel is not available. 8 Cancel the test tone function. DVD TEST TONE VOL. CH LEVEL CH SEL ENTER or RPT A TITLE 7. 1 SURR INTRO B RETURN AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE TEST TONE TUNER CD T1/MON AUX PHONO VID1 VID2 VID3 VID4 VID5 SYS DISP SLEEP DIRECT IN ROOM2 HOME THEATER MASTER RNC-220 23 ENGLISH Adjusting each channel level 4 Adjust the level of the selected channel as desired. ENGLISH Downmixing into 2 front channels Allows the multi - channel signals encoded in DTS, Dolby Digital or MPEG format to be reproduced through only two front speakers or through headphones. When the digital signals from the DTS, Dolby Digital or MPEG program sources are input, press the STEREO button. To cancel the 2 - CH downmix mode, select the desired surround mode with using the MULTI CONTROL knob or the DSP MODE button, etc. When the playback of the source on the player is stopped or interrupted, etc, the 2 - CH downmix mode is not canceled even though " DTS", "DOLBY DIGITAL" or "MPEG" indicator goes off. If headphones are plugged in and the SPEAKER button is set to off while the digital signals from the DTS, Dolby Digital or MPEG program sources are being input, it will enter the 2- CH downmix mode automatically and if headphones are unplugged and the SPEAKER button is set to on while in the 2 -CH downmix mode, it will return to the previous mode. DVD STEREO VOL. CH LEVEL CH SEL ENTER RPT A TITLE INTRO B or 7. 1 SURR RETURN AUTO DSP MODE ST DISC P. SCAN TEST TONE CENTER MODE ST TUNER CD T1/MON AUX PHONO VID1 VID2 VID3 VID4 VID5 SYS DISP SLEEP DIRECT IN ROOM2 HOME THEATER MASTER RNC-220 "DTS", "MPEG"or "DOLBY DIGITAL" indicators lights up and "2CH DOWNMIX" is scrolled, meaning it enters the 2 - CH downmix mode, and then the discrete multi-channels(except LFE) are mixed down into 2 front channels. 24 LISTENING TO RADIO BROADCASTS Auto tuning 1 Select the tuner. 2 DVD Select the desired band. BAND BAND FREQUENCY AUDIO VOL. [. . . ] 1 Vp-p S-Video(luminance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (chrominance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 286 Vp-p Component video(R-Y signal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5 Vp-p (B-Y signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]