User manual SHIMANO ALTUS SI-R917A

[. . . ] · There are two different types of reinforced connecting pin available. Be sure to check the table below before selecting which pin to use. If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting pin or tool which is not suitable for the type of chain is used, sufficient connection force may not be obtained, which could cause the chain to break or fall off. Chain 9-speed super narrow chain such as CN-7701 / CN-HG93 8- / 7- / 6-speed narrow chain such as CN-HG50 / CN-IG51 Reinforced connecting pin Silver 6. 5mm Cassette sprocket tooth combination Model number CS-HG50-8I CS-HG40-8I MF-HG40-7 MF-HG37 Sprockets 8 8 7 7 Group name an ao az ax Tooth combination 11, 13, 15, 17, 20, 23, 26, 30T 11, 13, 15, 17, 20, 23, 26, 34T 14, 16, 18, 20, 22, 24, 34T 14, 16, 18, 20, 22, 24, 28T Installation of the freewheel To install Tightening torque: 30 Nm {260 in. [. . . ] We strongly recommend that only genuine Shimano replacement parts be used. · Keep these Technical Service Instructions in a safe place. The 6 sprockets are secured by means of rivets. Sprocket spacers (1. 0mm) Lock ring Note · Always be sure to use the sprocket set bearing the same group marks. Group marks Never use in combination with a sprocket bearing a different group mark. · Because the high cable resistance of a frame with internal cable routing would impair the SIS function, this type of frame should not be used. · Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides. Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way. · Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly. · Operation of the levers related to gear shifting should be made only when the front chainwheel is turning. · For smooth operation, use the specified outer casing and the bottom bracket cable guide. · The SC-C050 speedmeter, SC-C051 odometer and SC-C052 clock and stopwatch are available as separate items. Please ask your bicycle dealer for further details. · Parts are not guaranteed against natural wear or deterioration resulting from normal use. · For maximum performance we highly recommend Shimano lubricants and maintenance products · For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer. ag -18T ag -15 T · For installation of the sprockets, use the special tool (TL-HG16) to tighten the lock ring. Tightening torque: 30 - 50 Nm {261 - 434 in. lbs. } TL-HG16 ag -13 T · To replace the sprockets, use the special tool (TL-HG16) and TL-SR20 to remove the lock ring. Disassembly 5 mm allen key Installation of the rear derailleur When installing, be careful that deformation is not caused by the B-tension adjustment screw coming into contact with the dropout tab. 5 mm Allen key <RD-MR40> Direct-mount type Push in and tighten Tightening torque: 8 - 10 Nm {70 - 86 in. lbs. } 5 mm Allen Key Technical Service Instructions SI-R917A Shoud be touching Rear Drive System Before use, read these instructions carefully, and follow them for correct use. Dropout tab B-tension adjustment screw Bracket type Tightening torque: 3 - 4 Nm {26 - 34 in. lbs. } Bracket nut Frame In order to realize the best performance, we recommend that the following combination be used. Series REVOSHIFT Outer casing Rear derailleur Type Freehub Sprockets Cassette sprocket Chain Bottom bracket cable guide Altus SB-C055A-8R SIS RD-CT95 Smart Cage FH-CT91 8 CS-HG50-8I CS-HG40-8I Tourney 40 SB-C055A-7R SIS RD-MR40-7 MGS -- 7 MF-HG40-7 Bracket spindle tightening torque: 8 - 10 Nm {70 - 86 in. lbs. } Bracket bolt Bracket Chain length Add 2 links (with the chain on both the largest sprocket and the largest chainring) Largest sprocket Largest chainring CN-HG50 / CN-UG50 SM-SP18 / SM-BT18 Chain Checking the chain connection Chain gauge TL-CN24 Specifications Rear Derailleur Model number Type Total capacity Largest sprocket Smallest sprocket Front chainwheel tooth difference Applicable front chainwheel (chainring tooth configuration) RD-CT95 Smart cage 43T 34T 11T 20T FC-CT92 (42-34-24T) RD-MR40-7 MGS 40T For IG, chains, insert the chain gauge (TL-CN24) into the inner link which is next to the chain connecting pin to check that the inner link width is correct. Check that the connecting pin pro-trudes past the outer link by the same amount on both sides, and that the amount of protrusion is 0. 2 mm or more. 2. 38mm Connecting pin A, B Q 0. 2mm A B 1=2. 38mm TL-CN24 SHIMANO JAPAN CHAIN GAUGE 1=2. 38mm TL-CN24 SHIMANO JAPAN CHAIN GAUGE 34T 13T 20T FC-TY33A (48-38-28T) Connecting pin Outer link Correct U . S . [. . . ] Connecting and securing the inner cable Replace the inner cable by carrying out steps to as shown in the illustrations. For the best SIS performance, periodically lubricate all power-transmission parts. Gear shifting operation Pedaling becomes lighter Pedaling becomes heavier Installation of the switch Remove the switch cap and install the switch as shown in the illustration. Inserting the inner cable Insert the inner cable into the outer casing from the end with the marking on it. Apply grease from the end with the marking in order to maintain cable operating efficiency. Marking SHIMANO JAPAN CHAIN GAUGE Switch Switch cap 1=2. 38mm TL-CN24 Cutting the outer casing Inner link When cutting the outer casing, cut the opposite end to the end with the marking. After cutting the outer casing, make the end round so that the inside of the hole has a uniform diameter. Outer end cap This service instruction explains how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. [. . . ]