User manual SHURE PGXD WIRELESS QUICK START GUIDE REV 2

[. . . ] · Professional quality 24-bit digital audio · Digital RF technology for rock-solid performance System Components All systems include · PGXD4 receiver · Power supply · User guide · 2 AA alkaline batteries Vocalist systems include · PGXD2 handheld transmitter · Microphone clip * Available only in select markets · Microphone head (choice of PG58, SM58®, SM86, Beta 58A® or Beta 87A*) · Wide variety of rugged and dependable Shure microphones · One-touch setup and operation · Up to 10 hours of battery life (9 hours, PGXD2) · Up to 200 foot range (line-of-sight) · 900 MHz operation--free from white spaces or DTV interference Lavalier, Headworn, and Instrument systems include · PGXD1 bodypack transmitter · Microphone (choice of WL93, WL185, PG30 or Beta 98H/C) Guitar systems include · PGXD1 bodypack transmitter · 1/4" to mini 4-pin guitar cable (WA302) Receiver Controls and Connectors PGXD4 audio LED Indicates strength of incoming audio signal: green for normal, amber for strong and red for clipping. Infrared (IR) port Sends IR signal to transmitter for sync. sync button Press to synchronize transmitter with receiver group and channel settings. LED Screen Displays group and channel setting. See "Single System Setup" for details. channel button Changes group and channel setting. [. . . ] Note: The amber LED may appear to be red when viewed at an angle. For best results, monitor the LED from directly in front. Bodypack Transmitter The bodypack has 26 dB of audio gain adjustment. · Increase gain (clockwise +) for microphones · Decrease gain (counterclockwise ­) for guitars or high-output instruments Handheld Transmitter Access the gain switch by unscrewing the head of the microphone. Use the tip of a pen or a small screwdriver to move the switch. · 0dB: For quiet to normal vocal performance. · ­10dB: Use only if audio is distorted due to high vocal levels. BIAS AUDIO 0dB -10dB PGXD AUDIO 0dB -10dB 3 Single System Setup Scan Use the scan feature on the receiver to find a clear channel. Synchronize Synchronize the transmitter to the receiver by aligning the infrared (IR) ports and pressing the sync button. Make sure the IR ports are closely aligned. After a successful sync, the transmitter LED momentarily flashes red and the receiver ready light illuminates. LED screen displays current channel channel press channel button to scan for a clear channel system scans for the channel with the least interference NOTE: This wireless system may be affected by RF interference when used in proximity to other wireless devices such as cordless phones, baby monitors, and two-way radios. For best results, use the scan and sync feature before each use or if you experience problems. Multiple System Setup Use the following steps to ensure the best performance when installing multiple wireless systems at the same location. Turn all receivers on and all transmitters off. Note: Turn on any other digital equipment that could cause interference during the performance so it will be detected during the frequency scans in the following steps. Make sure the group number is the same for all receivers (see Manual Group Selection). Perform a scan using the first receiver. Turn on the first transmitter and sync it to the receiver. · Important: After syncing each transmitter, leave it on so that scans from the other receivers will not select that channel. Compatible Frequencies · Be sure only one transmitter IR port is exposed when synchronizing each system. When operating multiple systems simultaneously, choose one group from the following table and set all systems to different channels within that group. Number of Systems 2 3 4 5 Group (by band) X8 3 to 9 3 to 9 3 to 9 7 to 9 X8A (Austrailia) 3 to 9 3 to 9 --- X8B (Brazil) 3 to 9 3 to 9 3 to 9 -- 4 Manual Channel and Group Selection (receiver only) Using the receiver to scan for a channel is the best way to find the best frequency for your system. However, for multiple system setup, you may need to manually set the group number. Hold the button until the channel or group display begins flashing. Release and press the button again to advance the setting. [. . . ] Certified by IC in Canada under RSS-210 and RSS-102. (IC: 616A-PGXD1, 616A-PGXD2, 616A-PGXD4). PGXD1, PGXD2 PGXD4 Certified under FCC Part 15. (FCC ID: DD4PGXD1, DD4PGXD2). Approved under the Declaration of Conformity (DoC) provision of FCC Part 15. [. . . ]