User manual SHUTTLE MK40V

[. . . ] MK40V/MK40VN AMD AthlonXP 462-pin Processor with 200/266/333 MHz FSB Based DDR MAINBOARD User's Manual Shuttle® MK40V/MK40VN AMD AthlonXP 462-pin Processor with 200/266/333 MHz FSB Based DDR Mainboard Manual Version 1. 1 Copyright Copyright© 2003 by Shuttle® Inc. This publication, including all photos, illustrations, and software, is protected under international copyright laws, with all rights reserved. Reproducing any of the material contained herein is prohibited without the consent of the publisher. Disclaimer Shuttle® Inc. shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. [. . . ] Clearing CMOS will result in the permanently erasing previous system configuration settings and the restoring original (factory-set) system settings. 1 Pin 1-2 (Normal) 1 Clear CMOS1 1 Pin 2-3 (Clear CMOS) Step Step Step Step Step Step Step A2 1. Turn off the system power (PC-> Off). Remove ATX Power cable from ATX Power connector. Place the jumper cap on pins 2-3 for a few seconds. Plug ATX Power cable into ATX Power connector. Turn on the system power (PC-> On). CPU Frequency Setting (JP3) JP3 are used to set the CPU frequency (100MHz to 166 MHz) according to the CPU. CPU Frequency 133 MHz 166 MHz 100 MHz 200MHz (Reserve) Pins 1-2 Off Off On On Pins 3-4 Off On Off 1 JP3 2 On - 25 - F Back Panel Connectors B1 B2 PS/2 Mouse & PS/2 Keyboard Port Connectors Two 6-pin female PS/2 Mouse & Keyboard connectors are located at the rear panel of the mainboard. Depending on the computer housing you use (desktop or tower), the PS/2 Mouse connector is situated at the top of the PS/2 Keyboard connector when the mainboard is laid into a desktop, as opposed to a tower where the PS/2 Mouse connector is located at the right of the PS/2 Keyboard's. Plug the PS/2 Mouse and Keyboard jacks into their corresponding connectors. PS/2 Mouse PS/2 Keyboard B3 COM1 Port Connector Attach a serial device cable to the DB9 serial port COM1 at the back panel of your computer. COM1 Port B4 Parallel Port Connector One DB25 female parallel connector is located at the rear panel of the mainboard. Plug the connection cable from your parallel device (printer, scanner, etc. ) into this connector. Parallel Port B5 VGA Port Connector One 15-pin VGA connector is located at the rear panel of the mainboard. VGA Port - 26 - B6 USB1/2/3/4 Port Connectors This mainboard offers 4 USB ports on back panel. Plug each USB device jack into an available USB1/2/3/4 connector. USB Port2 USB Port4 USB Port1 USB Port3 B7 LAN Port Connector (MK40VN only) This mainboard can accommodate one device on LAN. Attach RJ-45 cable to this port connector to your PC to the LAN. LAN Port B8 Line-In Port Connector Line-In is a stereo line-level input port that accepts a 1/8-inch TRS stereo plug. It can be used as a source for digital sound recording. Line-In Port B9 Line-Out Port Connector Line-Out is a stereo output port through which the combined signal of all internal and external audio sources on the board is output. It can be connected to 1/8-inch TRS stereo headphones or to amplified speakers. Line-Out Port B0 1 Mic-In Port Connector Mic-In is a 1/8-inch jack that provides a mono input. It can use a dynamic mono or stereo microphone with a resistance of not more than 600 Ohms. Mic-In Port - 27 - F Front Panel Connectors C1 HDD LED Connector (HDLED) Attach a connector cable from the IDE device LED to the 2-pin (HDLED) header. The HDD LED lights up whenever an IDE device is active. MSGLED PWR NC 1 HDLED RST RSVD PANEL1 Note : Please notice all the LED connectors are directional. If your chassis's LED does not light up during running, please change it to the opposite direction. C2 Hardware Reset Connector (RST) Attach a cable to the 2-pin (RST) header. Pressing the reset switch causes the system to restart. MSGLED PWR NC 1 HDLED RST RSVD PANEL1 - 28 - C3 MSG LED Connector (MSGLED) Connecting MSG LED a single- or dual-color, front panel mounted LED provides power on/off, sleep and message waiting indication. MSGLED PWR NC 1 HDLED RST RSVD PANEL1 C4 ATX Power On/Off Switch Connector (PWR) The Power On/Off Switch is a momentary type switch used for turning on or off the ATX power supply. Attach a connector cable to the 2-pin (PWRSW) header on the mainboard. MSGLED PWR NC 1 HDLED RST RSVD PANEL1 - 29 - C5 Extended USB Header (USB2) The header is used to connect the cable attached to a USB connector which is mounted on front panel or back panel. But the USB cable is optional at the time of purchase. Pins Assignment: 1=VREG_FP_USBPWR0 2=VREG_FP_USBPWR0 3=USB_FP_P04=USB_FP_P15=USB_FP_P0+ 6=USB_FP_P1+ 7=GROUND 8=GROUND 9=KEY 10=USB_FP_OC0 2 USB2 1 C6 Front Panel Audio Header (AUDIO1) This header allows users to install an auxiliary Front-Oriented Microphone and Line-Out port for easier access. [. . . ] Ø The choice: Auto, Enabled or Disabled. Ethernet Device Use this item to set the onboard AC'97 Ethernet LAN. Ø The choice: Enabled or Disabled. OnBoard USB Function Enable this item if you plan to use the USB ports on this mainboard. [. . . ]