User manual SIEMENS GIGASET A390

[. . . ] 1 Gigaset A390 The handset at a glance 1 Charge status of the batteries 2 Display keys 3 Message key Flashes: new messages received 4 Directory key 5 Control key (u) 6 Talk key 7 End call key and On/Off key 8 Ringer tone on/off (press and hold in idle status) 9 Keypad lock on/off (press and hold) 10 Recall key - Consultation call (flash) - Dialling pause (press and hold) 11 Microphone 12 "Microphone off" key 1 11. 12. INT 2 3 4 5 6 7 11:56 MENU U h Please note Charge the handset for 18 hours before first use. 8 9 10 11 12 Display key on handset: Pressing a key launches the function that appears above that key in the display. Display INT MENU " U T ~ OK Function when pressed Call other registered handsets page 12. Open main/submenu (see Menu tree page 15). [. . . ] After the initial charging procedure a complete charging to full capacity takes at least 18 hours. e U (flat to full) e flashes: batteries almost flat U flashes: charging Setting the date and time Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm can be used. MENU Settings OK Date/Time OK Date: ~ (enter the day, month and year in the format dd/mm/yy) OK Time: ~ (enter hours and minutes in 24-hour format) OK a (press to return to idle status) ¢ ¢ ¢ ¢ ¢ ¢¢ ¢ ¢ ¢ ¢ Please note When entering the time and date, you can move the position of an entry to the left or right by pressing the control button up or down. 8 Display in idle status Once the phone is registered and the time set, the idle display is shown as in this example. U 11. 12. INT 11:56 MENU Activating/deactivating the handset Press and hold the a key to activate or deactivate the handset. If you place a deactivated handset in the base station or charging cradle, it will automatically activate. Your phone is now ready for use. If you have any questions about using your phone, please read the tips on troublepage 14). shooting ("Questions and answers" ¢ 9 Making calls Making external calls and ending calls External calls are calls using the public telephone network. ~ (Enter the phone number) The phone number is dialled. (Or you can first press and hold c to hear dial tone and then enter the number. ) During the call you can adjust the earpiece volume using t and set the volume with u. End the call/cancel dialling: Press the end call key a. Muting You can mute your handset when making external calls. Press the "Microphone off" key m during the call to activate/deactivate the function. ¢c. Using the directory and lists Directory To open the directory: press or h (A390 only). You can save up to 80 phone numbers (max. 32 digits) with corresponding names (max. ters Accepting a call The handset indicates an incoming call by ringing and by a display on the screen. Press the talk key c to accept the call. When Auto Answer is activated (see Menu page 15), simply remove the handtree set from the base station/charging cradle. In idle status, use t to activate the menu for setting the call volume and use u to set the volume. ¢ ¢ Saving the first number in the directory h ¢ New Entry?¢ OK ¢ ~ (enter number) ¢ OK ¢ ~ (enter name) ¢ OK Storing a number in the directory h ¢ MENU ¢ New Entry ¢ OK ¢ ~ (enter number) ¢ OK ¢ ~ (enter name) ¢ OK Selecting a directory entry Open the directory with h. You have the Use u to scroll through the entries until the required name is selected. following options: Calling Line Identification When you get a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory or if CNIP has been requested. Preconditions: 1 You have asked your network provider for the caller's number (CLIP) to be displayed on your handset screen. 2 The caller has asked the network provider for his number to be identified (CLI). Enter the first character of the name and scroll to the entry with u, if required. ® appears in the display if you have not requested Calling Line Identification, Withheld appears if the caller has withheld CLI, and Unavailable appears if the caller has not requested CLI. 10 Dialling with the directory h ¢ u (select entry) ¢ c Using other functions h ¢ u (select entry) ¢ MENU The following functions can be selected with u: New Entry Managing entries in the last number redial list c (press briefly) ¢ u (select entry) ¢ MENU You can select the following settings: Use Number Save new phone number. Copy to Dir. Delete Entry Delete List Show Number Display the phone Use Number Edit Entry Delete Entry Delete List Send List number. [. . . ] Problem Cause Solution Base station power consumption In standby mode ­ Handset in base station ­ Handset outside base station During a call approx. 1. 0 W General specifications DECT standard WDCT standard Range Operation time (DECT version) ­ Talk time ­ Standby time Operation time (WDCT version) ­ Talk time ­ Standby time Base station power supply Environmental conditions in operation *) country-specific is supported* is supported* up to 300 m outdoors up to 50 m indoors up to 12 hours up to 177hours up to 6 hours up to 144 hours 100/240 V~, 50 Hz +5 °C to +45 °C, 20% to 75% relative humidity Press the end call key a for approx. 5 seconds or place the handset in the base station. The batter- Charge or replace the ies are flat. [. . . ]