User manual SIEMENS GIGASET SL37H

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset SL37H Gigaset Handset at a glance 17 16 INT 1 V 1 2 15. 11. 07 ? 09:45 SMS 3 15 14 13 12 4 5 11 10 9 8 6 7 Please note: Illustration of handset on a base station with SMS functionality. 1 Display (screen) in idle status 2 Charge status of the battery pack = e V U (flat to full) = flashes: battery pack almost flat e V U flashes: battery pack charging 3 Display keys (page 9) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status), Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Connection socket for headset and PC interface 9 Microphone 10 Recall key - Consult (flash) - Insert a dialling pause (press and hold) 11 Star key Ringer tones on/off (press and hold), With an open connection: switch between dial pulsing/touch tone dialling (press briefly), Open special characters table 12 Key 1 Select answer machine (depending on the base station)/network mailbox (press and hold) 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold) When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Flashes: incoming call 15 Control key (page 8) 16 Bluetooth activated (page 26) 17 Signal strength i (high to low) | flashes: no reception 1 Contents Contents Handset at a glance . 3 Gigaset SL37H More than just a telephone . Installing the base station and charging cradle . [. . . ] s Select a language and press OK. a Press and hold (idle status). Starting the function, dialling the number If the handset is in idle status, press and hold the numerical key or press the display key briefly. Depending on the key assignment: u Numbers are dialled directly. u The function menu is opened. If you accidentally choose a language you do not understand: w N 4 Press keys in sequence. s Select the correct language and press OK. Setting the display You have a choice of four colour schemes and several different contrasts. w Display Colour Scheme Select and press OK. s Select a colour scheme and press OK ( = current colour). a Press and hold (idle status). Changing key assignments Display key key. The list of possible key assignments is opened. Proceed as is described when first assigning the key with a shortcut (page 18). Press and hold the left or right display Digit key Change Press the digit key briefly. The list of possible key assignments is displayed. Proceed as is described when first assigning the key with a shortcut (page 18). 19 First steps Setting the screensaver You can set a picture from the Resource Dir. (page 22) to be displayed as a screensaver when the handset is in idle status. This will replace the idle status display. The screensaver is not displayed in certain situations, e. g. during a call or if the handset is de-registered. If a screensaver is activated, the Screen Saver menu option is marked with . w Display Screen Saver The current setting is displayed. Change multiple line input: Activation: Select On (screensaver is displayed) or Off (no screensaver). Selection: If required, change the screensaver (see below). If the screensaver conceals the display, briefly press a or w to show the idle display with time and date. Setting the display backlight Regardless of whether or not the handset is in the charging cradle, you can activate or deactivate the backlighting. If the handset is switched on, the display is permanently dimmed. w Display Backlight The current setting is displayed. [. . . ] data cables page 32) are plugged into the connection socket (page 1), Bluetooth is automatically deactivated. If a Bluetooth voice connection has already been established, Bluetooth is not deactivated until it is ended. If a Bluetooth data connection has already been established, the response depends on the receiving device. Bluetooth is automatically reactivated when the accessories are removed. [. . . ]