User manual SIEMENS LF958BA60B

[. . . ] S Operating and installation instructions Fig. 1 ELECTRO Table of contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information on protection of the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before using the appliance for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 4 5 5 5 6 7 7 8 8 8 9 10 11 11 11 12 13 13 14 15 15 16 17 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An activated carbon filter must be installed to bind odours in circulating-air mode (see "Removing and installing the grease filters"). The complete installation set as well as the replacement filters are available from specialist outlets, customer service or the Online Shop. To switch on the acoustic signal, repeat the process. Fan follow-on Press the button. The fan continues to run at step 1 for 10 minutes, and at the same time a dot flashes in the display. After this period the fan switches off automatically. 9 Cleaning and care LOOKING AFTER THE APPLIANCE Suitable cleaning agents and care products for your appliance can be purchased via the Hotline or from the Online Shop (see cover page). Metal-mesh grease filters The metal-mesh grease filters absorb the grease particles from the kitchen fumes. The filter mats consist of fire-proof metal. RISK OF FIRE As the filters become more saturated with greasy residue, the flammability increases. The function of the extractor hood may also be impaired. The risk of fire is prevented by cleaning the metal-mesh grease filters in good time. When cleaning the grease filters, also remove grease deposits from the accessible parts of the housing with a damp cloth. Appliance surfaces NOTE: Observe the warranty regulations in the enclosed service booklet. The appliance surfaces and controls are scratch-sensitive. Therefore observe the following cleaning instructions: ­ Avoid cleaning the extractor hood with dry cloths, abrasive sponges, scouring agents, cleaning agents containing sand, soda, acid, chlorine or any other aggressive substances. ­ Clean the appliance surfaces and controls with a soft, damp cloth, washing-up liquid or a mild window cleaner only. ­ Do not scrape off dried dirt, but moisten with a damp cloth. ­ Clean carefully in the area of the controls to avoid liquid from getting into the electronics. NOTE: Clean the stainless steel surfaces in the direction of the ground surface only!Do not use stainless steel cleaner for the control buttons! Cleaning the metal-mesh grease filters . . . Under normal operation (daily 1 to 2 hours), the metal-mesh grease filters must be cleaned 1x month. . . . in the dishwasher The metal-mesh grease filters can be cleaned in the dishwasher. Slight discolouration may occur but this will not affect the function of the grease filters. The filters must be placed loosely in the dishwasher. NOTE: Do not clean heavily saturated metalmesh grease filters together with utensils. . . . by hand When cleaning by hand, soak the grease filters in a hot detergent solution, brush off the dirt, rinse thoroughly and leave to dry. [. . . ] The enclosed screws and wall plugs are suitable for concrete and natural stone. Use the appropriate fasteners for other ceiling structures. Ensure that the ceiling has adequate load bearing capacity. Ensure that the depth of the drilled holes corresponds with the length of the screws. [. . . ]