User manual SIEMENS LI44630/01 INSTALLATION INSTRUCTIONS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SIEMENS LI44630/01. We hope that this SIEMENS LI44630/01 user guide will be useful to you.
Lastmanuals help download the user guide SIEMENS LI44630/01.
Manual abstract: user guide SIEMENS LI44630/01INSTALLATION INSTRUCTIONS
Detailed instructions for use are in the User's Guide.
[. . . ] The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.
Do not flambé food directly under the extractor hood. Risk of grease filter catching fire due to flames.
The hotplates must always be covered with a utensil. Restrictions apply to the use of the extractor hood over a solid-fuel burner (coal, wood, etc. ). The appliance is not intended for use by young children or infirmed persons without supervision. [. . . ] Press the notch on the inner filter and fold the filter down.
Filters and maintenance
Inserting the grease filter: 1. Press the filter to the back, until the magnets take hold.
Filters and maintenance
Metal filters are used to trap the greasy element of the vapours that develop during cooking. Caution: As the filter becomes more and more saturated with grease, not only does the risk of it catching fire increase but the efficiency of the extractor hood can also be adversely affected. Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: # When the grease filters reach saturation point, an acoustic signal is sounded for 6 seconds after the fan has switched off, and an # appears in the display. Cleaning the metal grease filters: In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned 1 x a month. The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc.
When cleaning the filters by hand, soak them in hot soapy water first of all. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. Press the 0 button.
Cleaning and care
Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine!The smaller the gap between the extractor hood and hotplates, the greater the likelihood that droplets will form on the underside of the extractor hood. Additional information concerning gas cookers: When installing gas hotplates, comply with the relevant national statutory regulations (e. g. Always comply with the currently valid regulations and installation instructions supplied by the gas appliance manufacturer. Only one side of the extractor hood may be installed next to a high-sided unit or high wall. Minimum distance on gas hotplates between the upper edge of the trivet and lower edge of the extractor hood: 650 mm, Fig. 40
5 mind. 5
min. 800 max. 1080
The exhaust air is discharged upwards through a ventilation shaft or directly through the outside wall into the open. D Exhaust air should neither be directed into a smoke or exhaust flue that is currently used for other purposes, nor into a shaft that is used for ventilating rooms in which stoves or fireplaces are also located. Exhaust air may be discharged in accordance with official and statutory regulations only (e. g. Local authority regulations must be observed when discharging air into smoke or exhaust flues that are not otherwise in use. D When the extractor hood is operated in exhaust-air mode simultaneously with a different burner which also makes use of the same chimney (such as gas, oil or coal-fired heaters, continuous-flow heaters, hot-water boilers) care must be taken to ensure that there is an adequate supply of fresh air which will be needed by the burner for combustion. Safe operation is possible provided that the underpressure in the room where the burner is installed does not exceed 4 Pa (0. 04 mbar). [. . . ] Ensure that the minimum distance between the hob and the extractor hood is maintained 550 mm for an electric hob and 650 mm for a gas hob. The bottom edge of the template corresponds to the lower edge of the extractor hood (glass screen). Drill 3 x l 8 mm holes for the extractor hood and 2 x l 8 mm holes for the chimney panelling. Insert plugs into the holes so that they are flush with the wall.
05. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SIEMENS LI44630/01
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SIEMENS LI44630/01 will begin.