User manual SIEMENS MQ955

[. . . ] The following installation-steps can be done by everyone. The SANTIS-ab can be wall-mounted or placed on the desk (piling of more units is also possible). In case of wall mounting, drill the holes into the wall according to the enclosed drawing, insert dowels with wood screws and hang on the SANTIS-ab. · 6 · Connection of the terminal equipments: The sockets for the analog equipments (e. g. telephones, gr. 2/3 fax machines, modems) are designated with «a/b1» and «a/b2», those for the ISDN terminal equipments with «S» (e. g. [. . . ] If the NT+2ab mode is selected, all the configuration commands can be set from both the a/b-interfaces without any restrictions. · · 8 If the configuration access (CA) is restricted (can be set and changed by authorized persons, e. g. telecom staff), the configuration for the a/b1-interface can only be done via the a/b1-interface and vice versa for the a/b2-interface. If the Pairgain mode is selected, the configuration access is automatically restricted, i. e. the configuration for the a/b1interface can only be done via the a/b1-interface and vice versa for the a/b2-interface. 9 The settings are executed as follows. Dial the command number and parameter value according to the tables in chapter 5. Dial # If the parameter has been programmed successfully, a permanent tone is switched on. Otherwise a busy tone will be switched on. if necessary for setting other parameters or hook on. 10 Start: Hook off Dial Input command number Input parameter value Dial # no Setting over?Table of Configuration Commands Parameter-Reset Command-No / Meaning 010 reset of all parameters to the default value Parameter value 1 Default --- All parameters having a default value are affected. The default values are set in the factory and can be reseted by this command. and Pairgain: A parameter reset via the a/b1-interface affects only a/b1parameters and vice versa for a/b2. and Pairgain: a/b1 via a/b1 only; a/b2 via a/b2 only. 19 Call Waiting Tone Switch Command-No / Meaning 341 call waiting tone at a/b1-interface 342 call waiting tone at a/b2-interface Parameter value 0 = off 1 = on 0 = off 1 = on Default 1 1 The call waiting tone is a tone in the receiver signaling an incoming call during a call is already ongoing. This service is not available at every network provider. The incoming call can be answered by finishing the ongoing call (hook on, SANTIS-ab rings, hook off). The call waiting tone can be switched off, e. g. if a fax machine or a modem is connected to the a/b-interfaces. and Pairgain: a/b1 via a/b1 only; a/b2 via a/b2 only. 20 Metering Calculation Command-No / Meaning 380 amount for one metering pulse 390 currency factor Example for US$: 1 pulse = 10 cents, thus dial Parameter value 1 to 8 digits 1 to 8 digits Default country specific country specific 380 10 # 1 US$ = 100 cents, thus dial 390 100 # Restrictions for NT+2ab/CA restr. and Pairgain: Can only be set by authorized persons. 21 Calling Line Identification Restriction (CLIR) Switch Command-No / Meaning Parameter value Default 411 CLIR at 0 = ident. allowed In the ISDN world the number of the caller is submitted to the called party. CLIR means `Calling Line Identification Restriction', i. e. [. . . ] When a permanent tone is switched on, hook on. 23 Configuration Example 2: A fax machine gr. 3 is connected to the a/b1-interface. Thus the MSN and HLC are to be set: MSN = 456, HLC = fax gr. 2/3 for a/b1. Hook off and wait for dial tone, then dial 2. the dial tone is switched off 111 456 # 1st MSN for a/b1 dial 3. When the permanent tone is switched on proceed to 4 and 4. 221 2 # HLC for a/b1 5. [. . . ]