User manual SILVERCREST 10 IN 1 UNIVERSAL REMOTE CONTROL V2.2

[. . . ] Universal ReMOte COntROl IAN: 33137 COMAG Handels AG Zillenhardtstraße 41 D-73037 Göppingen universal remote Control Operation and Safety Notes Yleiskaukosäädin Käyttö- ja turvaohjeet Bruksanvisning och säkerhetsanvisningar universalfjärrkontroll Last Information Update · Tietojen tila · Informationsstatus: 06 / 2009 · Ident. -No. : 062009-3 A 3A 3A 100% Black+Silver for light surfaces GUarantEE m ·· 3 6 PleaSe cut thiS carD anD encloSe it to the returning gooD Sender please use block-writing in boxes with CAPITAL LETTERS Surname Firstname Street Postcode and city Telephone no. with area code o n th s ·· ·· f ro m p urc h as coMag Service centre unit 1 longs industrial estate englands lane gorleston great Yarmouth norfolk nr31 6Be Service-hotline: 00 44 (0) 8708 900137 e-mail: info@comag-ag. co. uk Universal remote Control Signature of buyer Faulty-Description: # -d e a te ra Gua ntee ·· Universal Remote Control 10 in 1 Instruction manual Version 2. 2_GB, 08. 06. 2009 Technical data, design, equipment and items supplied subject to change. Introduction This instruction manual explains the · intended use, · safety measures · advantages of this universal remote control (to be known as the remote control). This instruction manual does not describe in detail how to use the remote control with your device. Please see the information and instructions in the manual for your device. [. . . ] Operate the combi device like two separate devices. Combi devices with one device code Other combi devices only require one code. First you must select the part of the device that you wish to use next. Example: The device is a combined DVD recorder / Video recorder. The device code is stored under the source button. To operate the DVD part of the combi device press and hold the source button for longer than a second. To switch to using the video recorder in the combi device, briefly press the setup button for the shift function, then the source button. If your combi device only requires one device code, but you wish to use it with two source buttons, one for each part of the device, then proceed as follows: 29 Program the device code onto two source buttons. Operate one part of the device with one of the two source buttons. Use the learn function to transfer the desired functions of the other part of the device onto the other source button. 30 System set up options / Punch Through The "Punch Through" (VOL/MUTE) function enables you to use the volume and mute functions on another type of device other than the one currently being used. Image transmission devices that connect to a TV (e. g. DVD, VCR, SAT, CBL) often do not have their own volume control. If the universal remote control is currently operating such a device and the VOL (Volume) or (Mute) buttons are pressed then they will operate the volume control of the TV. Settings for the punch through function, time, date, backlighting and system reset: (System Setup Menu Structure) 31 Programming Punch Through (VOL / MUTE) onto another type of device You can set up the universal remote control so that the Punch Through function operates another device rather than the TV. The device must obviously have a volume control function. Hold down the setup (17) button for about 3 seconds until is shown. Press the setup button (17) once more to bring up . The display will show . Press OK (12) Press OK (12) again. This menu allows you to program all VOL/MUTE commands of one type of device which you will select in the next step. The question will appear on the display. Select the device that you wish the VOL/MUTE operation to be changed by using one of the source buttons (2). The message and the confirmation will be shown shortly after each other. [. . . ] keep it away from direct sunlight. 61 Hints and Tips / Troubleshooting Symptoms The display remains dark Possible Cause and Remedy Check that the batteries are inserted correctly in the remote control and that the polarity + /­ is correct. If the batteries do not have enough power, exchange them for new ones. There are several device codes listed under the manufacturer of my device. The devices will only react to certain commands from the remote control. [. . . ]