User manual SILVERCREST KH 2130

[. . . ] 6 RADIO SET KH 2130 Operating instructions Radio Set KOMPERNASS GMBH BURGSTRASSE 21 D-44867 BOCHUM www. kompernass. com ID-Nr. : KH 2130-06/09-V3 KH 2130 Konformitätserklärung gemäß dem Gesetz über Funkanlagen und Telekommunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE) Declaration of Conformity in accordarice with the Radio and Telecommunications Terminal Equipment Act (FTEG) and Directive 1999/5/EC (R&TTE Directive) Hersteller / Verantwortliche Person Manufacturer / responsible person Kompernaß GmbH Burgstraße 21 44867 Bochum Funkübertragungs-Set Radio Transmission Set erklärt, dass das Produkt declares that the product Type (ggf. Anlagenkonfiguration mit Angabe der Module): KH 2130 Type (if applicable, configuration including the modules) Telekommunikations(Tk-)endeinrichtung Telecommunicätions ternlinal equiprrient Verwendungszweck / lntended purpose Funkanlage Radio equipment Übertragung von Audio und Video Signalen Transmission of audio and video signals bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des § 3 und den übrigen einschlägigen Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht. complies with the essential requirements of §3 and the other relevant provisions of the FTEG (Article 3 of the R&TTE Directive), when used for its intended purpose. Gesundheit und Sicherheit gemäß § 3 (1) 1. (Artikel 3 (1) a)) Health and safety requirements pursuant to § 3 (1) 1. [. . . ] · This device is not intended for use by individuals (including children) with restricted physical, physiological or intellectual abilities or deficiences in experience and/or knowledge unless they are supervised by a person responsible for their safety or receive from this person instruction in how the device is to be used. Children must be supervised to ensure that they do not play with the device. Damage to the device · Do not expose the radio transmission set to high temperatures, direct sunlight, severe vibrations or high mechanical loads. · Do not use any aggressive chemical substances for cleaning. -5- The device components Fig. A: The transmitter: q Transmitter w LED status indicator e Switch ROOM 1 r Switch ROOM 2 t Infrared connection socket (IR) y Output for a TV u AV input 2 i AV input 1 o Connection socket a Transmitter's on/off switch s Transmitter channel toggle switch (on the underside of the device) Fig. B: The receiver: d Receiver f Infrared receiver g LED operating indicator h Audio/Video CINCH outputs j Connection socket for the supply voltage k Receiver's on/off switch l Reception channel switch (bottom of device) 1( Wall plug transformer (2 pieces) 2) CINCH--3, 5mm jacks cables (2 pieces) 2!SCART--CINCH adapter "IN" 2@ SCART--CINCH adapter "OUT" 2# Infrared cable with 3 transmit diodes 2$ AUDIO adapter 3. 5 mm mini-stereo to CINCH female 2% CINCH--CINCH cable Putting the device into use First take all device components from the packaging and remove all packing foil and tape. Important notice: Even when the system (transmitter + receiver) is switched off, the manufacturer still recommends disconnecting the wall plug transformer from the mains power or using a power strip with a shut-off switch. Only in this way is complete switch off assured thus contributing to economical consumer attitude. Connecting the transmitter Note: You can connect two signal sources. The signal to be transmitted can be selected via a switch on the front panel of the transmitter. Thereby the radio transmission set can transmit the image and sound signals of every device that emits a sound and/or video signal via a suitable connection: · DVD Player / CD Player · VCR · Television · SAT receiver/set top box · Video camera · Computer video card, etc. Connecting signal sources to the transmitter: · On devices with cinch outputs for the audio and video signals you connect these via one of the supplied CINCH-- 3, 5mm jack cables 2) to the socket "AV IN 1" i on the rear panel of the transmitter q. -6- Note: Observe the colour coding: The white CINCH plug carries the left audio channel signal and belongs in the white CINCH socket. The red CINCH plug carries the right audio channel signal and belongs in the red CINCH socket. The yellow CINCH plug carries the video signal and belongs in the yellow CINCH socket. · If required you can connect a second device as well, with the transmitter and for this select the socket "AV IN 2" u. · If the signal source of your signal is available via a SCART connection, you can use the supplied SCART-- CINCH adapter "OUT" 2@ between the device and the CINCH--3, 5mm jack cable 2). · The A/V output of your signal source is now occupied. If you, nevertheless, want to connect the signal source to a TV, connect the TV via the socket "OUTPUT TO TV" y to the transmitter q. For this you can use either one of the supplied CINCH--3, 5mm jack cables 2) or, if both are already occupied, an equivalent cable from your local dealer. · For this you connect the supplied infrared cable 2# to the transmitter's infrared connection socket t. · Select on the transmitter and on the receiver, via the CHANNEL switch s and l, implicitly in each case the same transmission channel. The radio transmission should now function. Note: The data/signals sent from the transmitter are not encrypted. This means that compatible devices within the reception range are capable of eavesdropping on the signal. [. . . ] Make sure that the transmitter q and the receiver d have the same setting. If you are using other radio devices (same frequency), this may result in disruptions. It may also affect the range of the radio transmission set. Disruptions in remote control commands Point your remote control directly at the infrared receiver f. [. . . ]