User manual SILVERCREST KH 2189

[. . . ] If a battery is swallowed medical assistance must be sought IMMEDIATELY. Power consumption: Power consumption Standby: Protection class: Radio frequency range: FM (VHF) : AM (MW) : 87, 5 ­ 108 MHz 526, 5 ­ 1606, 5 kHz To avoid potentially fatal electric shocks: · Connect the device only to correctly installed and earthed mains sockets. Ensure that the rating of the local power supply tallies completely with the details given on the rating plate of the device. · Make sure that the power cable never becomes wet or damp during operation. Lay the cable such that it cannot be trapped or otherwise damaged. The technical capabilities of this device make possible an adjustable frequency range that lies beyond the permitted frequency ranges of 87, 5 ­ 108 MHz and 526, 5 ­ 1606, 5 kHz. [. . . ] direct sunlight, heaters, other devices, etc. · Keep children away from the connecting cable and the device. Children frequently underestimate the dangers of electrical devices. · Provide for a safe location for the device. · Do not operate the device if it has sustained a fall or is damaged. Arrange for the device to be checked and/or repaired by qualified technicians. Notice regarding separation from mains-power The slide switch AUTO/OFF/ON for this device does NOT completely separate it from the mains power source. Additionally, the device consumes power when in standby-mode. To completely separate the device from mains-power, the power plug MUST be removed from the wall socket. -3- Thunderstorm warning! Before a storm and/or a thunderstorm with a risk of lightning, please separate the device from the electrical power source! Commissioning Setup · Unpack the radio alarm and all ancillaries. · Remove all transport restraints and adhesive tape/films. Note: Check the condition of the battery for powerfailure protection annually, and replace it if necessary. Attention! Do not permit small children to play with the plastic packaging. · Position the radio alarm on a level and horizontal surface. Note: This device is equipped with non-slip rubber feet. As furniture surfaces may be made of a variety of materials and are treated with many different types of cleaning agents, it cannot be completely ruled out that some substances contain ingredients which may corrode the rubber rests and soften them. If possible place an anti-slip material under the feet of the device. Inserting the batteries Power-cut protection Through the insertion of a 9 V block battery (Type 6LR61/6F22) you will avoid that, in the event of a power failure, the functioning of the device is interrupted and, as a result, saved settings, such as time and alarm time, are lost. The battery ensures that the radio alarm continues to function with an emergency operation, also during a power failure. On restoration of the power supply, the correct time will appear automatically on the display s. Operating elements q w e r t y u i o a s d f g h j Power cable Battery compartment (on the underside) Cable aerial TIME button HOUR button MIN. OFF button Display Frequency scale Waveband selector switch FM/AM Note: The alarm, radio and display do not function with battery-power. · Open the battery compartment w and insert a 9 V block battery (Type 6LR61/6F22). Note: Rechargable batteries cannot be charged via the battery connection. In the event of an extended power cut (several hours), the clock and alarm times must be checked and possibly re-adjusted. TUNING-Regulator Slider switch AUTO/OFF/ON Volume regulator -4- Assembly Before operating the device, make sure that it is in a faultless condition. · Insert the plug into a power socket. Select a power socket that is at all times easily accessible, so that the plug can be quickly withdrawn in the event of a malfunction. Note: To improve reception in the FM frequency range, slowly move and hold the end of the wire aerial e in various directions. When you have found the best reception for the desired transmitter, fix the wire aerial into this position e. g. For the reception of AM transmitters, an aerial is built into the device. For improved reception, alter the position of the device in radio mode. Setting the clock When you take the device into use for the first time after inserting a new battery: Whilst pressing and holding the button TIME r: · Repeatedly press, or press and hold, the button HOUR t to set the hours. [. . . ] You can extend the time to switch off by. . . · pressing and holding the button SLEEP i and, at the same time, raise the switch off time to 1 hour and 59 minutes with the button HOUR t. You can reduce the time to switch off by . . . · pressing and holding the button SLEEP i and, at the same time, adjust the remaining time with the button MIN. [. . . ]