User manual SILVERCREST KH 2217

[. . . ] 6 PLL CLOCK RADIO KH 2217 PLL CLOCK RADIO Operating instructions KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM www. kompernass. com ID-Nr. : KH2217-08/08-V1 KH 2217 3@ 3# 3& KH 2217 ³ ¹ ¸ µ 3^ 2^ 2& 2* 3% 3( 3$ 3* 4@ 4! 2% 2$ 2# 2@ 2!3) 2( 4) CONTENT Safety instructions Intended use Items supplied Appliance overview Technical data Preparing for use Providing electrical power Using the clock Using the radio Cleaning the appliance Disposal Warranty and Service Importer PAGE 4 8 8 9 11 12 12 13 19 23 24 25 26 Read the operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference. Pass this manual on to whoever might acquire the appliance at a later date. -3- PLL CLOCK RADIO KH 2217 Safety instructions · This device has not been designed for use by people (including children) with restricted physical, sensory or intellectual abilities or lack of experience and/or knowledge, unless they are supervised by a responsible person (for their own safety) or have received instructions on how to use the device. Children should be supervised to ensure that they do not play with the device. [. . . ] Within 10 seconds repeatedly press the button MIN+ SET to switch between the 12-hour mode ("12Hr" blinks) and the 24-hour mode. Press the button BAND or wait a few seconds. In the 12-hour mode the indicator PM appears under the time display for the hours of the afternoon/evening. - 14 - Setting the alarm time You can programme in two different alarm times, AL1 and AL2. Alarm times can only be programmed with the radio switched off. The button HOUR+ SET can be pressed numerous times in succession or held down firmly. Press the button HOUR+ SET to set the hours. As soon as the desired hour indication is shown in the display for alarm time AL1, release the button. The button MIN+ SET can be pressed numerous times in succession or held down firmly. Press the button MIN+ SET, to set the minutes. As soon as the desired minute indication is shown in the display for alarm time AL1, release the button. Press the button AL1 SET or wait a few seconds. The programmed alarm time will be taken over. To programme in the second alarm time, repeat the steps 1 to 6. However, instead of pressing button AL1 SET, press the button AL2 SET. Press and hold the button SNOOZE/DISPLAY DIMMER until SNO and the minute indication appears on the display. Press the button MIN+ SET to programme the minutes. As soon as the desired after-call period is displayed, release the button. The programmed after-call period is taken over. Note: Should a second alarm time be pending during an activated snooze function, the second alarm time will eventually switch itself on and, if need be, the snooze function must once again be reactivated. Adjusting the display brightness Mains power operation: 1. Press the button SNOOZE/DISPLAY DIMMER at intervals of 2 seconds. The display brightness changes itself as follows: Bright>Medium>Dark>Bright - 17 - Battery operation: To save energy, the display illumination is deactivated in battery operation. Projection of the time For the time display to be well visible on a wall or ceiling, the room must be darkened. Important: The time display projection is created with an LED. [. . . ] All adjustments made by yourself are erased. Cleaning the appliance Important: NEVER use benzine, solvents or cleaners that can cause damage to plastics, as they could damage the appliance!· Keep the appliance and the ventilation openings clean at all times. · Fluids may not, under any circumstances, penetrate into the interior of the appliance · Never use aggressive cleaners. · For cleaning the housing and the display use a soft and slightly moist cloth. - 23 - Disposal Do not dispose of the appliance in your normal domestic waste. [. . . ]