User manual SILVERCREST KH 528

[. . . ] · Immediately remove the plug from the socket should you hear or smell anything unexpected from the appliance when it is in use or there is an evident malfunction. · NEVER operate the appliance when it is empty, i. e. without ingredients in the mixing attachment. To reduce the risk of fire or injury: · NEVER insert your hand or fingers in the mixing jug, especially when it is in use. · DO NOT open the cover when the appliance is in operation. Should you do so, pieces of the foodstuff could be thrown out at high speeds! [. . . ] ­ that the power cable y is not in the working area and thus not presenting a risk of being inadvertently snagged and tipping the appliance over. Position the appliance such that, . . . -3- Operation Warning! The motor switches itself off as soon as the mixing jug e is removed from the motor block u. It could then be overlooked that the appliance is still switched on. The motor will thus start of its own accord as soon as the mixing jug e is replaced on it: Therefore: · First insert the power plug into the wall socket when the mixer jug e is filled and mounted with its lid fitted and closed. · Before mounting the mixing jug always check to see that the appliance is switched off or that the power plug has been removed. · Before removing the mixer jug e, switch the appliance off, remove the power plug and wait for the motor to stop revolving. Selecting operating speeds When the mixer jug e is filled, completely sealed and securely fitted to the motor block u, you can then switch the appliance on. Place the switch t on . . . ­ Level 1-3 for fluid or soft foodstuffs, for mixing, blending and stirring ­ Level 3-5 for firmer foodstuffs or for hacking ­ Level Ice Crush/Clean for short, powerful impulse operation, e. g. the crushing of ice cubes, grinding of hard foodstuffs or for cleaning. So as not to overburden the motor, the switch t does not engage in this position. Hence, hold the switch t in this position for short periods only. Notice Fill the mixer attachment e with a maximum of 180 g of ice cubes. If filled with more than this, the appliance cannot optimally crush them. Filling and mounting the mixer jug ake the mixer attachment e from the motor unit u and remove the lid w. IFill the mixer attachment e and then press the lid w firmly back onto the mixer attachment e. Insert the filling cap q into the lid opening and secure it by turning it clockwise. Place the ready filled and sealed mixer jug e onto the motor block u. Lightly turn the mixer jug e until you can press it down. The motor can start only when the mixer jug e is securely positioned. Filling when in use Warning! Should you wish to insert further foodstuffs during operation, you may ONLY open the filling cap q provided for this purpose. · Under no circumstance should you open the lid w. Pieces of the foodstuff could be thrown out at high speeds!· Do not insert cutlery items or mixing tools into the mixing jug e when the appliance is in use. There is a considerable risk of injury should these make contact with the swiftly rotating cutters r!To insert something when the appliance is in operation, . . . turn the filling cap q anti-clockwise and remove it. Afterwards, replace the filling cap q into the lid and secure it by turning it clockwise. -4- Removing the mixer When the processing of the foodstuffs is complete: Always first place the switch t into the OFF position ("0") and remove the power plug. Wait until the motor has come to a complete standstill before lifting the mixer jug e straight up. [. . . ] Under no circumstances should you use a hard object, this could damage the contact switch. Remove any possible residues on the underside of the motor block u only with a dry cloth or a stiff bristled brush. Ensure that nothing can enter through the ventilation opening of the appliance. After cleaning Allow all parts to dry well before re-assembling and re-using the liquidiser. Remove the mixer jug e from the motor block Turn the plastic element u. of the mixer attachment e anti-clockwise, such that it allows itself to be released from the glass element . Storage If you do not intend to use the liquidiser for an extended period, clean it thoroughly (see chapter "Cleaning"). Wrap the power cable y around the cable storage i on the base of the motor block u. [. . . ]