User manual SILVERCREST KH 700

[. . . ] 6 FOOD PROCESSOR KH 700 Food Processor Operating instructions KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM www. kompernass. com ID-Nr. : KH700-10/09-V2 KH 700 1 r 2 e t z 3 w u I q II 4 0 III IV V 9 5 VI i 6 7 8 o CONTENT 1. Appliance description / Items supplied 2. Assembling the food processor PAGE 2 2 2 2 3 3 6. 1 Fitting the mixing bowl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6. 2 Fitting the lid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6. 3 Insert the ingredient by filling shaft and pusher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7. Working with the mixing bowl 4 7. 1 Working with the cutting blade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7. 2 Remove the cutting and grating blades from the accessory clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7. 3 Insert the cutting and grating discs back into the accessory clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7. 4 Working with the cutting and grating discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7. 5 Working with the kneading blade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 8. [. . . ] Working with the mixing bowl The supplied accessories for the mixing bowl 9 consist of 6 grating and cutting discs (I-VI), a kneading blade t and a chopping blade z. The mixing bowl 9 is very versatile to use: grating or cutting, mixing or cutting, kneading or stirring. · Place the lid 0 on the mixing bowl 9. · Insert the ingredients into the mixing bowl 9 through the loading shaft q. · Place the stodger w in the loading shaft q. · Now switch on the appliance by setting the speed controller 7 to the level recommended in the table. If you are uncertain about the speed, use the fastest level (3). -4- Hints: · Cut the ingredients into approx. 3 cm size pieces before adding them to the bowl 9. · The appliance chops the ingredients very fast, therefore allow the appliance to run only briefly. · Do not allow the appliance to run for more than 1 minute at a time. · Should the ingredients get caught up in the bowl 9 or between the blades z: - Switch off the appliance. - Remove the lid 0 from the mixing bowl 9. - Remove the ingredients with a spatula o. 7. 3 Insert the cutting and grating discs back into the accessory clip · Insert the cutting discs (II/III) in the retainer slots. Begin with the inner retainer slots. The lateral flaps with the elevation in the middle must point upwards. Make sure that all the cutting edges are pointing inwards. · Place the shredder (IV/V), grater (I) and potato-chips disc (VI) in the storage slot on the outside. 7. 2 Remove the cutting and grating blades from the accessory clip · Remove the blender lid 2 from the blender jug 4 by turning it clockwise. · Grasp the accessory clip 3 on the handle at the centre of the retainer 3 with the thumb and index finger. · Place the accssory clip 3 back in the blender jug 4. Ensure that the rails on the accessory mounting 3 grip firmly into the shoulders of the mixing container 4. · Place the cover 2 on the liquidiser 4 so that the arrows on the handle of the liquidiser 4 and on the cover 2 point towards each other. Turn the cover 2 anti-clockwise until it sits firmly. · Pull the accessory clip 3 with the cutting and grating discs (I-VI) out of the blender jug 4. · Remove the cutting and grating discs (I-VI) from the holder 3. 7. 4 Working with the cutting and grating discs Caution: · The cutting edges are very sharp!Exercise inserting and removing or cleaning the discs!· Never use your fingers, spatula, spoon handles or similar objects for pushing foodstuff through the filling shaft q! -5- The cutting (II/III) and grating discs (IV/V) can be used to slice or grate food stuffs quickly. The special potato-chip disc (VI) enables you to make uniform potato-chips at home. [. . . ] Only in this way can a post-free despatch for your goods be assured. The warranty covers only claims for material and maufacturing defects, but not for transport damage, for wearing parts or for damage to fragile components, e. g. This product is for private use only and is not intended for commercial use. The warranty is void in the case of abusive and improper handling, use of force and internal tampering not carried out by our authorized service branch. [. . . ]