User manual SILVERCREST SEKU 2000 A1

[. . . ] 6 Electric Fireplace SEKU 2000 A1 Electric Fireplace Operating instructions KOMPERNASS GMBH BURGSTRASSE 21 · D-44867 BOCHUM www. kompernass. com ID-Nr. : SEKU 2000 A1-05/10-V3 Contents Introduction . 2 Information for these operating instructions . 8 Individual parts of the electric fireplace . . 17 Notes on the EC Declaration of Conformity . [. . . ] Dispose of packaging material that is no longer needed according to the regionally established regulations. NOTICE If possible preserve the appliance's original packaging during the warranty period so that in the case of a warranty claim you can package the appliance properly for return. SEKU 2000 A1 5 Setting up and connecting Installation requirements For the safe and correct operation of the appliance, the installation site must satisfy the following requirements: GB IE The appliance must be placed on a firm, flat and horizontal surface. Do not place the appliance in a hot, wet or very humid environment or close to inflammable materials. The mains power socket must be easily accessible at all times, thus enabling the plug to be immediately withdrawn should an emergency situation arise. Ambient temperature range: +5 to +45 °C Humidity (No condensation): 5 - 90 % DANGER Fire hazard due to material contact!If the heater makes contact with flammable materials, there is a risk of fire!Pay heed to the following safety information to avoid these fire risks: Keep inflammable materials well away from the place of installation of the appliance. Prevent the physical contact of combustible materials (e. g. Do not cover the warm air outlet openings of the appliance. Before the first use Remove all packaging materials and transport restraints from the appliance. NOTICE When you first use it, it may temporarily generate a light odour. This is normal and completely harmless. Electrical connection For a safe and correct operation of the appliance, take note of the following instructions regarding the electrical connection: Before you connect the appliance, compare the connection data (voltage and frequency) on the plate with that of your electricity supplier. This data must tally, in order to avoid damage to the appliance. Ensure that the power cable is undamaged and that it is not placed over hot surfaces and/or sharp edges. The connecting cable must not be taut. 6 SEKU 2000 A1 Operating components Operating components NOTICE The operating elements are on the front of the appliance, above right and behind the ventilation grille. To operate them, fold the ventilation grille forward. GB IE 4 3 2 5 2 3 4 5 ON/OFF switch (Flames) ON/OFF switch (Heating, level 1) ON/OFF switch (Heating, level 2) Temperature control (Thermostat) Dimmer (for flame lamps) SEKU 2000 A1 7 Set up GB IE Set up Before the appliance can be set up, the fire surround must be assembled. NOTICE Check the contents to make sure everything is there and for visible damage. Turn the adapter sleeves with the screwdriver so that the arrows on the adapter sleeves each point to the outer edge of the centre front panel 5 . Insert four double locking pins C in the upper holes on the front sides of the panel and turn the adapter sleeves E with the screwdriver to the right until the locking pins are firmly secured. C C E 5 Step 4 Now connect the so prepared centre front panel E 5 with the side panels prepared in steps 1 and 2. For this, insert two adapter sleeves in the large holes in the side panels. Turn the adapter sleeves E with the screwdriver so that the arrows on the adapter sleeves each point to the outer edge of the side panels. Then, guide each of the double locking pins in the edges of the side panels. C of the centre front panel 5 5 into the corresponding holes When done, turn all four adapter sleeves E in the centre front panel until all parts are at right angles to each other and firmly tightened. with the screwdriver to the right, E E 5 SEKU 2000 A1 11 Assembly Step 5 GB IE Place the floor plate 7 on the floor. Now take the previously assembled unit and carefully place it on the floor plate as shown in the following diagramme. Then screw together the assembled unit with the connection blocks 8 screws of the type A . (2 screws per connection block). G on the floor plate 7 . For this, use G G A A Step 6 Take the top covering panel 3 and place it on the preassembled unit. 3 Secure the top covering panel from the inner side of the unit with 7 screws of the type A. 3 A 12 SEKU 2000 A1 Assembly Step 7 Take the base plate 6 and insert 4 wood plugs 6 B 7 into the holes of the plate underside. so that the four wood plugs fit into the four holes in Then place the base plate the floor plate. on the floor plate GB IE Rear view Front View 6 B 7 B Installing the appliance in the fire surround To finalise, install the appliance in the assembled fire surround. [. . . ] Insert the plug into the mains power socket. Check the fuses Replace the defective bulbs. Set the thermostat 4 at the required temperature. Inform Customer Services. The appliance does not heat. The fan does not run. The heating is not switched off. falsely adjusted. 4 Temperature control defect. NOTICE If you cannot solve the problem with the aforementioned methods, please contact Customer Services. Storage/Disposal Storage Disconnect the plug if you are not intending to use the appliance for a long period. [. . . ]