User manual SILVERCREST SL 65-12

[. . . ] Overview of equipment Front side of the receiver Overview of equipment PleaSe cuT ThiS caRd and encloSe iT To The ReTuRning good 100% Black+Silver for light surfaces Guarantee m ·· 3 6 Front side of the receiver 1 2 3 4 5 ­ LED display CH- key CH+ key Standby key Infrared sensor for the signals of the remote control Shows the channel location in operating mode. Switches to the next lower channel location Cursor moves down Switches to the next higher channel location Cursor moves up Switches on and switches to the standby mode The default settings will be restored if you keep this key pressed for more than 10 seconds. By doing this, your personal settings will be deleted. Sender please use block-writing in boxes with CAPITAL LETTERS Surname o n th s ·· ·· Firstname f ro m p urc h as Street Service centre Tony denyer Postcode and city Rear side of the receiver Telefon no. with areacode unit 1 longs industrial estate englands lane gorleston great Yarmouth norfolk nR31 6Be Service-hotline: 00 44 (0) 8708 900137 e-mail: info@comag-ag. co. uk Rear side of the receiver 1 2 3 4 LNB IN IF OUT VCR (output) TV (output) RS 232 + DC 11V ­ 14V COAXIAL AUDIO L AUDIO R LNB connection for the antenna cable LNB connection for a second satellite receiver SCART connection for the video set SCART connection for the TV set Serial port Connection 12V/power pack Digital coaxial audio output Stereo audio connection L(eft) Stereo audio connection R(ight) Model / type: Signature of buyer The remote control 5 6 7 8 9 Faulty-Description: # -d e a te ran Gua tee ·· DIGITAL CAMPING SATELLITE SYSTEM DIGITAL CAMPING SATELLITE SYSTEM COMAG Handels AG Zillenhardtstr. [. . . ] freight vehicles), please use a 24V/12V DC-DC converter. Otherwise, the receiver could suffer damages. You will lose your guarantee in case of non-observance. The receiver is supplied with preset TV channels and can be used immediately. If you want to check whether new channels are available, enable the automatic scan in the menu item Installation on page 73. 55 Getting started To switch over to the standby mode press the standby key (red key top right on the remote control or the key at the right side of the three keys at the face of the receiver). The LED display of the device shows the time in standby mode. 56 Getting started Fine adjustment of the antenna The reception quality set by you in the antenna settings may not be optimal. In this case, you must do a fine adjustment of the antenna. · Select a channel broadcasted on the satellite of your choice, e. g. Astra1 19° East channel location 1 = DAS ERSTE Press the "INFO" key. The current reception parameters are displayed. Please have a look at the signal-quality display during the following fine-tuning process. By pressing the 1 key, an acoustic signal is offered additionally to support you during the fine-tuning process. A stronger and higher signal indicates a better direction of the antenna. · · · As soon as the signal quality has reached approx. 60%, the channel image appears in the background. Should there be no image, you might have directed the antenna to another satellite instead of Astra1 19° In this case, . please proceed with the fine-tuning process as follows until you can see an image in the background. Please keep in mind that the signal-strength indication only shows the connection quality of the antenna to the receiver and is not intended to be used for directing the antenna. Initially you must set the antenna vertically at an approx. 1° steeper or flatter angle. 57 Getting started If you have connected the antenna in the case, loosen the wing nut on the case bar slightly. If you have installed the antenna in a different manner, loosen the wing nut on the supporting arm slightly. Turn the cover of the case or the supporting arm by approx. 1° . When you have found a position with good reception quality, you must tighten the wing nuts again to fix the antenna. [. . . ] With this you will make a positive contribution to pollution control. 94 Specifications Specifications Receiver Dimensions in mm (W × D × H) Weight in grammes 210 × 145 × 45 Receiver 553 g Remote control 80 g (without batteries) 950 MHz ~ 2'150 MHz 55 MHz / 8 MHz (below 5MS/s) 13V/18V GS, 0. 30 A max. overload protection 22 KHz ± 2 KHz, 0. 6 V pp ± 0. 2 V Version 1. 0, Version 1. 2, tone burst A/B 1 ~ 35 MS/s Max. 15 Mbit/s 1/2, 2/3, 3/4, 5/6, 7/8, auto 4:3 letterbox, 4:3 PanScan, 16:9 720 x 576 (Pal), 720 x 480 (NTSC) Left, right, stereo, AC3 digital sound Type F, IEC 169-24 Video CVBS, Audio L, R Video CVBS, Audio L, R Audio L, R Digital audio output Range of input frequency IF band width LNB power supply LNB control DiSEqC control Symbol rate Input speed Error correction (FEC) Aspect ratio Video resolution Audio mode Connection options LNB IF input TV SCART (output only) VCR SCART (output and input) RCA (CINCH) SPDIF, COAXIAL 95 Specifications Power supply Power pack input voltage Power pack output voltage Weight power pack in grammes Input voltage of the receiver Power consumption receiver 100-240 V ~, 50/60 Hz 12 V , 1. 0 A 108 11 ­ 14 V approx. 12 W (operation with Single LNB) approx. [. . . ]