User manual SIM2 HT300 E

[. . . ] 13. 1. 3 COLOR Use this control to adjust the colour level. 13. 1. 4 TINT Controls the purity of the colours, to NTSC coded signal standards. Tint is only applicable to video input with NTSC standard, to RGB 15kHz and YCrCb 15kHz inputs and YCrCb 32kHz (no RI2). 13. 1. 5 SHARPNESS Use this adjustment to increase and decrease the level of picture detail. [. . . ] 13. 2. 2. 5 Pixel to Pixel This aspect projects the signal as it is input without scaling up or down. Image is projected in the center of screen. 13. 2. 2. 4 User 1, 2, 3 Should you wish to use a format different to those preset, go to User menus. IMAGE ADJUSTMENTS POSITION ASPECT ADVANCED SETTINGS MAGNIFICATION VIDEO IMAGE ADJUSTMENTS MODE 4:3 POSITION ASPECT FREQUENCY/PHASE ADVANCED SETTINGS MAGNIFICATION 16:9 RGB 13. 2. 1 POSITION Use this adjustment to position the image vertically and horizontally. HORIZONTAL: VERTICAL: 9 6 ASPECT / USER 1 HORIZONTAL 0 VERTICAL -10 SCREEN CONTROL On Off 13. 2. 2 ASPECT Determines the aspect ratio of the projected image. From this menu it is possible to select the aspect ratio by using the numeric keys 1. . . 8 of the remote control. By using the Horizontal and Vertical adjustments it is possible to select the screen shape of your choice. It is important to keep the relation between height and width so that the correct aspect ratio can be maintained. If an appropriate screen-masking interface is connected to the 12V output socket " " it is possible to re-frame the screen to a variety of aspect ratios and screen sizes (please refer to the screen manufacturer's manual). 13. 2. 3 FREQUENCY / PHASE In the case of RGB graphic signals this adjustment is used for synchronization of the RGB image to the number of pixels on the DLP. ASPECT 1 NORMAL 2 ANAMORPHIC 3 LETTERBOX 4 PANORAMIC 5 PIXEL TO PIXEL 6 USER 1 7 USER 2 8 USER 3 Image aspect ratio selection FREQUENCY / PHASE FREQUENCY 1312 PHASE -12 By repeatedly pressing the key or by pressing the and one of the numeric keys 1. . . 8 of the remote control, it is possible to select the aspect ratio. RGB 13. 2. 2. 1 Normal This aspect projects the image occuping the full vertical dimension of the screen and maintaining the correct aspect (4:3 or 16:9). 13. 2. 3. 1 Frequency The correct frequency adjustment eliminates vertical band interference. 3 ENGLISH HT 300 13. 2. 3. 2 Phase The phase adjustment determines the stability and sharpness of the vertical lines in the projected image. 13. 2. 5 ADVANCED SETTINGS Advanced colour settings are accessible via this menu. 13. 2. 5. 2 Gamma correction Selects the Gamma's correction curve. It determines the projector's response to the grey scale, emphasizing - more or less - the different grades of brightness (blacks, dark, medium, light greys, whites) in the projected image. GAMMA CORRECTION ADVANCED SETTINGS GAMMA CORRECTION GAMMA CORRECTION Y/C DELAY 2 FILM VIDEO GRAPHICS VIDEO 13. 2. 5. 3 Y / C Delay Use this adjustment in the event of horizontal colour misalignment within the projected image. It is recom-mended that a colour bar test pattern be used for this adjustment. 13. 2. 6 MAGNIFICATION Use this adjustment to magnify the projected image (please note the higher the magnification the poorer the quality of the image projected). lens icon will appear at Select Zoom (the magnifying the centre of the image) to adjust the level of enlargement, using the Left and Right Arrows. ADVANCED SETTINGS COLOR TEMPERATURE GAMMA CORRECTION RGB We recommend the use of these settings only to the experienced user, as their adjustment can seriously affect final image quality. However it is possibile to return to optimal manufacturers settings, by selecting Reset. 13. 2. 5. 1 Colour temperature Select the colour temperature of the projected image. COLOR TEMPERATURE zione HIGH MEDIUM LOW USER Select Pan (zoom button on the remote control) to choose the area of image to enlarge, using all four arrow keys. There are three fixed colour temperature settings, which are: High (9000÷9500 degrees K), Medium (circa 6500 degrees K), Low (circa 5000 degrees K). The User option will allow you to select the colour temperature of your choice. COLOR TEMP. /USER RED 0 -16 GREEN 28 BLU Via remote control, it is possible to alternate between modes, by pressing the key on the keyboard pad. Alternatively pressing the -Focus-Esc button allows you to select between Zoom and Pan. 4 HT 300 13. 3 SETUP The installation menu gives access to features that will allow for correct installation of the projector. 13. 3. 3 PROJECTION LENS To adjust Focus and Size of the projected image, use the lens settings. SETUP ORIENTATION KEYSTONE PROJECTION LENS TEST PATTERNS FACTORY DAFAULTS PROJECTION LENS FOCUS ZOOM 13. 3. 1 ORIENTATION Select the option that best describes the installation i. e. [. . . ] 13. 4. 4 OSD TIMEOUT Use this adjustment to set the display time after which the On Screen Display will disappear. Left and Right Arrow keys set the timing (within a 5-60 second timeframe). 6 HT 300 15 INPUT SELECTION The Input Selection menu is recalled by pressing the key: O/AV of the remote control. During normal display, press Up Arrow key and Down Arrow key of the keyboard pad. The input selected will be highlighted in yellow. [. . . ]