User manual SIMRAD PROCESSOR UNIT OUTLINE SCHEMA REV A

[. . . ] Improper use or maintenance may cause damage to the equipment and/or injury to personnel. The user must be familiar with the contents of the appropriate manuals before attempting to install, operate or work on the equipment. Kongsberg Maritime AS disclaims any responsibility for damage or injury caused by improper installation, use or maintenance of the equipment. Support If you require maintenance on your Fish finding sonar system contact your local dealer. You can also contact us using the following address: -. [. . . ] The transceiver performs the transmission and reception control of the 480 transmitters and 480 receiver channels. 16 identical transceiver boards are used. A dedicated power supply is provided to supply the required DC voltages to the transceiver. One Ethernet cable is used for communication with the Processor Unit in the wheelhouse, and a second Ethernet cable is used to control the hull unit. The third Ethernet cable connects to the Power Supply Unit. The transducer cables from the hull unit are plugged into the side wall of the Transceiver Unit cabinet using a special plug. The Transceiver Unit is mounted on the bulkhead using powerful shock absorbers. The connectors for power and interface are located at the bottom of the cabinet. Power Supply Unit A dedicated power supply cabinet is used to provide the Transceiver Unit with operational power. Hull Unit The Hull Unit is designed to lower the transducer 1. 0 meters below the ship's hull. The transducer can also be lowered to any selected middle position. In case of voltage failure, the transducer can be raised or lowered manually by means of a hand crank. The sensor for the electronic stabilisation of the sonar beams is housed in the Motor Control Unit, which is mounted on the Hull Unit. 337405/A 7 Simrad PROCESSOR UNIT OUTLINE Transducer The cylindrical Transducer allows the sonar beam to give full 360 degrees coverage of the water volume down to -60 degrees. System diagram Figure 3 A B C D E F G H I PROCESSOR UNIT OUTLINE Simplified system diagram Processor Unit Colour Monitor Operating panel Operating Panel power supply Transceiver Unit Power Supply Unit Motor Control Unit (mounted on the hull unit) Hull Unit Transducer (mounted on the hull unit) 8 337405/A Simrad PROCESSOR UNIT OUTLINE Basic functionality The basic principles of the Simrad PROCESSOR UNIT OUTLINE are unique because of the 480 transmitter and 480 receiver channels with their transducer elements spread around on the cylindrical transducer. If you click on the middle of the button you will open a dedicated menu for mode selection. If you click on the right or left side of the button you can scroll through the available modes. C D E Tab: Click on a tab to bring forward the menu. Each menu holds one or more buttons. Button: Click on a button to change the applicable parameter. If you click on the middle of the button you will normally open a dedicated parameter dialog for parameter selection. If you click on the right or left side of the button you can scroll through the available choices. F Parameter dialog: When you click a button, the relevant parameter dialog opens at the bottom of the menu. Each parameter dialog holds one or more buttons or menus. To close a parameter dialog, click the Close button. Most dialogs provide a Help button for access to the on-line help. In this example you can see the Status dialog, which is replaced when a parameter dialog is opened. 14 337405/A Operating panel OPERATING PANEL The most frequently used functions are directly accessible by the designated control buttons on the Operating Panel, and may enter operational commands directly. [. . . ] The original installation drawings are available on PDF and/or AutoCad's DWG format. Visit www. simrad. com to download. Cabinet outline dimension drawings · Transceiver Unit dimensions on page 25 · Power Supply Unit dimensions on page 28 · Processor Unit dimensions on page 30 · Operating Panel dimensions on page 33 Hull unit outline dimension drawings · PROCESSOR UNIT OUTLINE Hull unit dimensions on page 34 · PROCESSOR UNIT OUTLINE Sonar trunk dimensions on page 35 · PROCESSOR UNIT OUTLINE Sonar trunk production on page 36 · PROCESSOR UNIT OUTLINE Blind cover dimensions on page 38 24 337405/A Drawing file Transceiver Unit dimensions Forward view 337405/A 25 Simrad PROCESSOR UNIT OUTLINE Side view 26 337405/A Drawing file Top view 337405/A 27 Simrad PROCESSOR UNIT OUTLINE Power Supply Unit dimensions Forward view 28 337405/A Drawing file Side view 337405/A 29 Simrad PROCESSOR UNIT OUTLINE Processor Unit dimensions Forward view 30 337405/A Drawing file Side view 337405/A 31 Simrad PROCESSOR UNIT OUTLINE Footprint 32 337405/A Drawing file Operating Panel dimensions 337405/A 33 Simrad PROCESSOR UNIT OUTLINE PROCESSOR UNIT OUTLINE Hull unit dimensions 34 337405/A Drawing file PROCESSOR UNIT OUTLINE Sonar trunk dimensions 5 920 20 5 12. 50 273 Material: Mild steel, St. 42 or better ø18 0. 3 12 Holes, spacing 30 degrees ø330 ø37 0 337405/A 35 Simrad PROCESSOR UNIT OUTLINE PROCESSOR UNIT OUTLINE Sonar trunk production Side view 36 337405/A Drawing file Top view 337405/A 37 Simrad PROCESSOR UNIT OUTLINE PROCESSOR UNIT OUTLINE Blind cover dimensions 38 337405/A Company profile COMPANY PROFILE Simrad Simrad is the world's most recognized brand in professional fish finding and fishery research equipment. The brand name "Simrad" is fully owned by Kongsberg Maritime AS. Through the history of Simrad, Kongsberg Maritime AS has more than 60 years of experience in design and manufacturing of advanced fishery sonars, echo sounders and catch monitoring systems. [. . . ]