User manual SKIL 1205

[. . . ] CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 50 144, EN 55 014, conforme aux rglementations 73/23/EEC, 89/336/EEC, 98/37/EEC. BRUIT/VIBRATION Mesur selon EN 50 144 le niveau de la pression sonore de cet outil est * dB(A) (1) et la vibration * m/s2 (2) (mthode main-bras). CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 50 144, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EWG, 89/336/EWG, 98/37/EWG. GERUSCH/VIBRATION Gemessen gem EN 50 144 betrgt der Schalldruckpegel dieses Gertes * dB(A) (1) und die Vibration * m/s2 (2) (Hand-Arm Methode). [. . . ] 10 Use safety glasses Also use face or dust mask, if cutting operation is dusty. 11 Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. 12 Do not abuse the cord Never carry the tool by the cord, never yank the cord to disconnect it from the socket, and keep the cord away from heat, oil and sharp edges. 13 Secure work Use clamps or a vise to hold the work; it is safer than using your hand and it frees both hands to operate the tool. 14 Do not overreach Keep proper footing and balance at all times. 15 Maintain tools with care Keep tools sharp and clean for better and safer performance. Follow instructions for maintenance and changing accessories. Inspect tool cords and plugs periodically and, if damaged, have them repaired by a qualified person. Inspect extension cords periodically and replace them, if damaged. Keep handles dry, clean and free from oil and grease. 16 Disconnect tools Disconnect tool when not in use, before servicing, or when changing accessories such as blades, bits and cutters. 17 Remove tool keys Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. 18 Avoid unintentional starting Do not carry a plugged-in tool with a finger on the switch. Be sure the switch is off when plugging in. 19 Outdoor use extension cords When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 20 Stay alert Watch what you are doing, use common sense and do not operate tool when you are tired. 21 Check damaged parts Before you use the tool, always carefully check the guarding and other parts to determine that they will operate properly and perform their intended functions. Check for alignment of moving parts, binding of moving parts and breakage of parts. Check for proper mounting of all parts and any other conditions that may affect their operation. A guard, switch or other part that is damaged or defective should be properly repaired or replaced by a qualified person. Do not use tool, if switch does not turn it on and off. Use the tool and its accessories in accordance with these safety instructions and in the manner intended for the particular tool, taking into account the working conditions and the work to be performed. [. . . ] 21 Contrlez si votre outil est endommag Avant d'utiliser l'outil, vrifiez toujours soigneusement le parfait fonctionnement des dispositifs de scurit et des pices. Vrifiez si le fonctionnement des pices en mouvement est correct, si elles ne se grippent pas ou si d'autres pices sont endommages. Tous les composants doivent tre monts correctement et remplir les conditions pour garantir le fonctionnement impeccable de l'outil. Tout dispositif de scurit, tout interrupteur ou toute autre pice endommage ou dfectueusedoit tre rpare ou remplace de manire approprie par un technicien qualifi. [. . . ]