User manual SKIL 1525

[. . . ] 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. [. . . ] 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR PLANERS Before using the tool check that the knives do not brush anywhere Keep your fingers away from the rotating knives Only use high speed steel (HSS) or carbide-tipped (TC) knife sets with this tool Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear away from the tool Wait for the cutter block to stop before setting the tool down (an exposed knife may engage the surface leading to possible loss of control and serious injury) Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/chip extraction when connectable If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If any chip should get jammed in the chip outlet, you should switch off the motor, ensure that all moving parts have come to a complete standstill, disconnect the plug, and remove the jammed chip Changing/reversing knives 3 This planer is equipped with non-grindable knives with cutting edges on both sides; so if one side has become blunt, the other side can be used !switch off the tool and disconnect the plug - remove guiding devices, if mounted - take wrench from storage A 2 - turn planer upside down - loosen 3 bolts B with wrench C (do not remove bolts) - remove clamping element D from cutter block E while pushing safety bracket F downwards - push knife out of clamping element with piece of wood (for easy removal clean knife first with petroleum or spirit) - for mounting a new or reversed knife handle viceversa (clean knife and clamping element first) !ensure that the clamping element rests on side stop of cutter block !groove in knife should match ledge in cutter block !ensure that knife end near safety bracket aligns with edge of foot (set a ruler flat against housing as illustrated and use it as a stopper) - firmly tighten 3 bolts B with wrench C !change/reverse knives in time; only use sharp knives !always change/reverse both knives at the same time !do not attempt to adjust the knives with cutter block screws G, which are pre-set at manufacturing Adjusting planing depth - turn knob H 2 to select required depth by using scale J2 - maximum planing depth 2. 5 mm - always select a shallow planing depth and repeat the planing and adjusting process until the required depth is reached Dust suction - when planing one may use a dust bag (SKIL accessory 2610387871) !do not attempt to remove any obstructions from the dust port K 3 while knives are rotating 6 Safety support L 4 - protects workpiece from damage when tool is put aside - will automatically fold backwards when planing Safety bracket F 3 - prevents contact with rotating knife - opens automatically when planing rabbets Operating the tool - adjust planing depth - place tool on workpiece !ensure that only the front shoe rests on the workpiece and that the knives do not touch it - switch on the tool by first pressing knob M 2 (= safety switch which cannot be locked) and then pulling trigger N 2 !before the knives reach the workpiece, the tool should run at full speed - hold the tool firmly with both hands and guide it forward in a continuous stroke - use the tool with its base-plate on the workpiece - do not tilt the tool in order to avoid unwanted planing marks - keep the ventilation slots uncovered !before switching off the tool, you should lift it from the workpiece - switch off the tool by releasing trigger N Planing rabbets - select required planing depth - select rabbeting depth by using rabbeting depth adjuster P 2 - adjust rabbeting width by using rip fence Q 3 - place tool on workpiece - start planing - maximum rabbeting width 82 mm - maximum rabbeting depth 24 mm GUARANTEE / ENVIRONMENT Always keep tool and cord clean (especially the ventilation slots) !CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 50 144, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EG, 89/336/EG, 98/37/EG. GERUSCH/VIBRATION Gemessen gem EN 50 144 betrgt der Schalldruckpegel dieses Gertes 87 dB(A), der Schalleistungspegel 100 dB(A), und die Vibration < 2, 5 m/s2 (Hand-Arm Methode). CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 50 144, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG. GELUID/VIBRATIE Gemeten volgens EN 50 144 bedraagt het geluidsdrukniveau van deze machine 87 dB(A), het geluidsvermogenniveau 100 dB(A), en de vibratie < 2, 5 m/s2 (hand-arm methode). CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 50 144, EN 55 014, enl. bestmmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG. LJUD/VIBRATION Ljudtrycksnivn som uppmtts enligt EN 50 144 r p denna maskin 87 dB(A), ljudeffektnivn 100 dB(A), och vibration < 2, 5 m/s2 (hand-arm metod). [. . . ] BUKA/VIBRACIJE Mereno u skladu sa EN 50 144, nivo pritiska zvuka ovog alata iznosi 87 dB(A), jaina zvuka 100 dB(A), a vibracija < 2, 5 m/s2 (mereno metodom na aci-ruci). IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti: EN 50 144, EN 55 014, v skladu s predpisi navodil 73/23/EG, 89/336/EG, 98/37/EG. HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 50 144 je raven zvonega pritiska za to orodje 87 dB(A), jakosti zvoka 100 dB(A), in vibracija < 2, 5 m/s2 (metoda `dlan-roka'). CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab jrgmistele standarditele vi normdokumentidele: EN 50 144, EN 55 014 vastavalt direktiivide 73/23/E, 89/336/E, 98/37/E nuetele. [. . . ]