User manual SKIL 1760

[. . . ] 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. [. . . ] Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMERS WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended OPERATING CONTROLS 2 A B C D E F G Switch for on/off and speed control Wheel for maximum speed control Button for switch locking Lever for changing direction of rotation Switch for selecting operating mode Locking sleeve Auxiliary handle Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Be careful not to drill or drive into areas where electrical wires may be contacted; always use auxiliary handle G2 Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/chip extraction when connectable If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always use auxiliary handle G 2 and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory 7 USE On/Off 3 Switch locking for continuous use 4 Speed control for smooth starting 5 Maximum speed control 6 With wheel B 2 the maximum speed can be adjusted steplessly from minimum to maximum Changing direction of rotation 7 - when not properly set in left/right position, switch A cannot be activated !change direction of rotation only when tool is at a complete standstill Selecting operating mode 8 1 = normal drilling/screwdriving 2 = hammer drilling 3 = chiseling !select operating mode only when tool is switched off - for drilling in wood, metal and plastic as well as for screwdriving the ring gear chuck and the corresponding adapter should be used (see: Application Advice) - the hammer mechanism is activated by applying a slight pressure on the tool when the drill bit is in contact with the workpiece - best hammer drilling results can be obtained by only a slight pressure on the tool needed to keep the automatic clutch engaged; drilling performance will not improve by applying more pressure on the tool: SKIL LETS THE TOOL WORK FOR YOU Changing bits 9 - clean and lightly lubricate accessory before insertion - pull back locking sleeve F and insert accessory in SDS+ chuck while turning and pushing it until it engages; the accessory locks in position automatically - pull accessory to check that it is locked correctly - remove accessory by pulling back locking sleeve F !the SDS+ accessory requires freedom of movement which causes eccentricity when tool is off-load; however, the accessory automatically centres itself during operation without affecting drilling precision !do not use bits/chisels with a damaged shank Safety clutch If the accessory gets jammed, the drive to the spindle is interrupted (causing a rattling noise) - immediately switch off tool - remove the jammed accessory - switch on tool again Adjusting drilling depth 0 Holding and guiding the tool !always use auxiliary handle G 2 (can be adjusted as illustrated) - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol * will remind you of this when the need for disposing occurs F APPLICATION ADVICE Use the appropriate bits @ !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 90 dB(A) and the sound power level 101 dB(A) (standard deviation: 3 dB), and the vibration 10. 7 m/s2 (hand-arm method). CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 73/23/EC, 89/336/EC, 98/37/EC. BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 90 dB(A) et le niveau de la puissance sonore 101 dB(A) (dviation standard: 3 dB), et la vibration 10, 7 m/s2 (mthode main-bras). CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EG, 89/336/EG, 98/37/EG. GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 90 dB(A) und der Schalleistungspegel 101 dB(A) (Standard- abweichung: 3 dB), und die Vibration 10, 7 m/s2 (Hand-Arm Methode). CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG. GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 90 dB(A) en het geluidsvermogen-niveau 101 dB(A) (standaard deviatie: 3 dB), en de vibratie 10, 7 m/s2 (hand-arm methode). CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG. LJUD/VIBRATION Ljudtrycksnivn som uppmtts enligt EN 60 745 r p denna maskin 90 dB(A) och ljudeffektnivn 101 dB(A) (standard deviation: 3 dB), och vibration 10, 7 m/s2 (hand-arm metod). CE KONFORMITETSERKLRING Vi erklrer under almindeligt ansvar, at dette produkt er i overensstemmelse med flgende normer eller normative dokumenter: EN 60 745, EN 55 014, i henhold til bestemmelserne i direktiverne 73/23/EF, 89/336/EF, 98/37/EF. STJ/VIBRATION Mles efter EN 60 745 er lydtrykniveau af dette vrktj 90 dB(A) og lydeffektniveau 101 dB(A) (standard deviation: 3 dB), og vibrationsniveauet 10, 7 m/s2 (hnd-arm metoden). [. . . ] BUKA/VIBRACIJE Mereno u skladu sa EN 60 745, nivo pritiska zvuka ovog alata iznosi 90 dB(A), a jaina zvuka 101 dB(A) (normalno odstupanje: 3 dB), a vibracija 10, 7 m/s2 (mereno metodom na aci-ruci). IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti: EN 60 745, EN 55 014, v skladu s predpisi navodil 73/23/EG, 89/336/EG, 98/37/EG. HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 60 745 je raven zvonega pritiska za to orodje 90 dB(A) in jakosti zvoka 101 dB(A) (standarden odmik: 3 dB), in vibracija 10, 7 m/s2 (metoda `dlan-roka'). CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab jrgmistele standarditele vi normdokumentidele: EN 60 745, EN 55 014 vastavalt direktiivide 73/23/E, 89/336/E, 98/37/E nuetele. [. . . ]