User manual SKIL 1765

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR INSTRUCTIONS INSTRUCTIONS HINWEISE INSTRUCTIES INSTRUKTIONER INSTRUKTION ANVISNING OHJEET INSTRUCCIONES INSTRUES ISTRUZIONI LERS POKYNY KILAVUZ page 7 page 10 Seite 13 bladz. 38 oldal 42 strana 45 sayfa 48 PL RU UA GR RO BG SK HR SCG SLO EST LV LT INSTRUKCJA O INSTRUCIUNI strona 51 55 59 62 pagina 66 KA3A POKYNY UPUTE UPUTSTVA NAVODILA INSTRUKCIJA INSTRUKCIJA 70 strana 73 stranica 77 stranica 80 stran 82 lappuse 89 puslapis 92 KASUTUSJUHEND leheklg 85 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 08/07 2610398010 1 1765 900 W 3, 3 kg 0-1100 13 28 40mm 0 - 5900 p/min 2 G D EF H C A B 3 4 2 5 6 7 8 A FWD FWD A REV REV 9 E F 3 0 ! @ G # 4 $ % HSS PHILLIPS POZIDRIV SLOTTED ^ & 5 * ( ) ACCESSORIES SKIL Nr. 13 mm 2610395660 6, 8, 10, 12, 16 mm 2610395766 6 GB Hammer INTRODUCTION 1765 This tool is intended for hammer drilling in concrete, brick and stone as well as for light chiseling work; for drilling in wood, metal and plastic as well as for screwdriving specific accessories should be used The hammering system in this tool outperforms any traditional ratcheting drill when drilling in concrete This tool is designed for use in combination with all standard SDS+ accessories Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H Switch for on/off and speed control Wheel for maximum speed control Button for switch locking Lever for changing direction of rotation Switch for selecting operating mode Unlocking button Locking sleeve Auxiliary handle SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. [. . . ] g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMERS Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator) Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/ chip extraction when connectable If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always use auxiliary handle H 2 and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off 4 Switch locking for continuous use 5 Speed control for smooth starting 6 Maximum speed control 7 With wheel B 2 the maximum speed can be adjusted steplessly from minimum to maximum Changing direction of rotation 8 - when not properly set in left/right position, switch A cannot be activated !change direction of rotation only when tool is at a complete standstill 8 Selecting operating mode 9 - press button F to unlock switch E - turn switch E to the desired operating mode until it snap-locks !start working only when switch E is locked 1 = normal drilling/screwdriving 2 = hammer drilling 3 = chiseling with rotating chisel 4 = chiseling with fixed chisel !select operating mode only when tool is switched off - for drilling in wood, metal and plastic as well as for screwdriving the corresponding adapter should be used (see: Application Advice) - the hammer mechanism is activated by applying a slight pressure on the tool when the drill bit is in contact with the workpiece - best hammer drilling results can be obtained by only a slight pressure on the tool needed to keep the automatic clutch engaged; drilling performance will not improve by applying more pressure on the tool: SKIL LETS THE TOOL WORK FOR YOU Chiseling with rotating chisel 0 !switch off the tool and disconnect the plug - select "rotating" chiseling mode Chiseling with fixed chisel !switch off the tool and disconnect the plug - select "rotating" chiseling mode - place chisel in desired position - select "fixed" chiseling mode Changing bits @ - clean and lightly lubricate accessory before insertion - pull back locking sleeve G and insert accessory in SDS+ chuck while turning and pushing it until it engages; the accessory locks in position automatically - pull accessory to check that it is locked correctly - remove accessory by pulling back locking sleeve G !the SDS+ accessory requires freedom of movement which causes eccentricity when tool is off-load; however, the accessory automatically centres itself during operation without affecting drilling precision !do not use bits/chisels with a damaged shank Safety clutch If the accessory gets jammed, the drive to the spindle is interrupted (causing a rattling noise) - immediately switch off tool - remove the jammed accessory - switch on tool again Adjusting drilling depth # Holding and guiding the tool $ - always use auxiliary handle H 2 (can be adjusted as illustrated) - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you APPLICATION ADVICE Use the appropriate bits % !Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 73/23/EC, 2004/108/EC, 98/37/EC. BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 95 dB(A) et le niveau de la puissance sonore 106 dB(A) (dviation standard: 3 dB), et la vibration m/s2 (mthode main-bras). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EG, 2004/108/EG, 98/37/EG. GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 95 dB(A) und der Schalleistungspegel 106 dB(A) (Standard- abweichung: 3 dB), und die Vibration m/s2 (Hand-Arm Methode). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 2004/108/EG, 98/37/EG. GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 95 dB(A) en het geluidsvermogen-niveau 106 dB(A) (standaard deviatie: 3 dB), en de vibratie m/s2 (hand-arm methode). Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. S CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 73/23/EG, 2004/108/EG, 98/37/EG. [. . . ] / EN 60 745 95 () i 106 () ( : 3 ), i /2 ( ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. UA GR CE YMBATOT : EN 60 745, EN 55 014, 73/23/EK, 2004/108/EK, 98/37/EK. Y / Y EN 60 745 95 dB(A) o 106 dB(A) ( : 3 dB), m/s2 ( / ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 07 SKIL Europe BV A. [. . . ]