User manual SKIL 1820T2

[. . . ] 1 1820 750 W 2, 4 kg 2 B A L 11000 S R F 3 C D 4 T E G 2 5 J H K Type 0 Type 10 Type 20 J 55x8x4 mm 60x10x4 mm J 65x12x4 mm J H H H 6 NM min. 50 mm 3 7 P O Q 8 X X 9 4 0 ! 5 @ # $ ACCESSORIES 100 x 50 x 50 x SKIL nr. 2610385169 2610385168 2610385167 2610385170 6 GB Plate joiner INTRODUCTION 1820 This tool is intended to route slots for biscuit connections in wood and similar materials Read and save this instruction manual TECHNICAL SPECIFICATIONS 1 SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. [. . . ] ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off locking switch - switch on tool by pushing switch A 2 forward !be aware of the sudden impact when the tool is switched on !before the blade reaches the workpiece, the tool should run at full speed - lock switch by pushing down front end of switch - unlock switch/switch off tool by pushing down back end of switch !before switching off the tool, you should pull it back from the workpiece Dust suction 3 - empty dust bag regularly for optimal dust pick-up performance - for using vacuum cleaner pull off dust bag C from vacuum cleaner adapter D and mount vacuum cleaner Front fence 4 - for keeping constant height when making joints - for proper guidance when cutting - suitable for 0/45/90 joints - front fence E can be adjusted for setting height with hex key F 2 (line of cut indicator G can be used as reference) Adjusting cutting depth 5 Your tool is equipped with a wheel allowing you to adjust the cutting depth for the plate size you wish to use (type 0, 10 or 20) - pull and turn wheel H to select required plate size - place tool with front fence against wall or piece of wood - push tool forward until it stops and hold it in that position - ensure that indicator J lines up slightly past selected size mark on scale; if not, use adjusting knob K Holding and guiding the tool !always use top handle B 2 for safe control and ease of operation - keep the ventilation slots L 2 uncovered Standard joint 6 - mark center of slot (at least 50 mm from outer edge of board) - in case of 2 or more slots allow at least 25 mm in between - for proper alignment mark all slots on both boards at the same time - align center line M on face plate N with your pencil mark - hold tool with both hands, switch it on and push it forward smoothly - after slot has been cut, pull back and switch off tool - repeat for all slots - insert plates "dry" to check whether they fit 8 - if satisfactory, apply good quality carpenter's glue (water-based) in all slots, insert plates into one side and press together !always store the plates in a dry place Changing blades 7 - take hex key F 2 from storage - remove front fence 4 - turn tool upside down - remove screws O and front P of base assembly - push spindle-lock button T 4 and hold it while you remove blade bolt Q counter-clockwise with a spanner 24 !push spindle-lock button T only when tool is at a standstill - change blade with arrow printed on blade pointing in same direction as arrow on housing - tighten blade bolt firmly by turning it clockwise while locking spindle - mount front of base assembly - mount front fence SECURITE INSTRUCTIONS GENERALES DE SECURITE ATTENTION!Le nonrespect des instructions indiques ci-aprs peut entraner un choc lectrique, un incendie et/ou de graves blessures sur les personnes. La notion d'outil lectroportatif mentionne par la suite se rapporte des outils lectriques raccords au secteur (avec cble de raccordement). 1) PLACE DE TRAVAIL a) Maintenez l'endroit de travail propre et bien clair. Un lieu de travail en dsordre ou mal clair augmente le risque d'accidents. b) N'utilisez pas l'appareil dans un environnement prsentant des risques d'explosion et o se trouvent des liquides, des gaz ou poussires inflammables. Les outils lectroportatifs gnrent des tincelles risquant d'enflammer les poussires ou les vapeurs. c) Tenez les enfants et autres personnes loigns durant l'utilisation de l'outil lectroportatif. En cas d'inattention vous risquez de perdre le contrle sur l'appareil. 2) SECURITE RELATIVE AU SYSTEME ELECTRIQUE a) La fiche de secteur de l'outil lectroportatif doit tre approprie la prise de courant. N'utilisez pas de fiches d'adaptateur avec des appareils avec mise la terre. Les fiches non modifies et les prises de courant appropries rduisent le risque de choc lectrique. b) Evitez le contact physique avec des surfaces mises la terre tels que tuyaux, radiateurs, fours et rfrigrateurs. Il y a un risque lev de choc lectrique au cas o votre corps serait reli la terre. c) N'exposez pas l'outil lectroportatif la pluie ou l'humidit. La pntration d'eau dans un outil lectroportatif augmente le risque d'un choc lectrique. [. . . ] , : EN 60 745, EN 55 014, 73/23/EEC, 89/336/EEC, 98/37/EEC. / co o EN 60 745 87 (A) e - 98 (A) ( : 3 dB), - < 2, 5 /2 ( ). CE , : EN 60 745, EN 55 014, 73/23/EEC, 89/336/EEC, 98/37/EEC. / EN 60 745 87 () i 98 () ( : 3 ), i < 2, 5 /2 ( ). [. . . ]