User manual SKIL 2005

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR INSTRUCTIONS INSTRUCTIONS HINWEISE INSTRUCTIES INSTRUKTIONER INSTRUKTION ANVISNING OHJEET INSTRUCCIONES INSTRUES ISTRUZIONI LERS POKYNY KILAVUZ page 7 page 10 Seite 13 bladz. 39 oldal 42 strana 46 sayfa 49 PL RU UA GR RO BG SK HR SRB SLO EST LV LT INSTRUKCJA O INSTRUCIUNI strona 52 56 60 63 pagina 67 KA3A POKYNY UPUTE UPUTSTVA NAVODILA INSTRUKCIJA INSTRUKCIJA 70 strana 75 stranica 78 stranica 81 stran 84 lappuse 90 puslapis 94 KASUTUSJUHEND leheklg 87 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 09/07 2610397841 1 2005 9, 6 V 1, 5 kg 8 Nm 2006 12 V 1, 5 kg 9 Nm 2007 14, 4 V 1, 6 kg 10 Nm 3-5 hours 3-5 hours 3-5 hours 550 10mm 5 12mm 4 mm 550 10mm 6 14mm 6 mm 550 10mm 6 16mm 8 mm 2 E E F C D A B 2 3 4 5 6 7 130C 8 9 0 NiCd ! G 3 5 H 3 @ # 4 $ % 20 1 ^ 5 & PHILLIPS POZIDRIV SLOTTED * ( ) 6 GB Cordless drill/driver INTRODUCTION 2005/2006/2007 This tool is intended for drilling in wood, metal, brick, stone, ceramic and plastic as well as for screwdriving in wood Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H On/off switch Switch for changing direction of rotation Keyless chuck Ring for torque control Ventilation slots Charger Green charging light Red charging light SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. [. . . ] b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR CORDLESS DRILL/ DRIVERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always check that the supply voltage is the same as the voltage indicated on the nameplate of the charger (chargers with a rating of 230V or 240V can also be connected to a 220V supply) In case of electrical or mechanical malfunction, immediately switch off the tool or unplug charger from power source SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator) Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Do not work materials containing asbestos (asbestos is considered carcinogenic) Take protective measures when during work dust can develop that is harmful to one's health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/ chip extraction when connectable Ensure that switch B 2 is in the middle (locking) position before making any adjustments or changing accessories as well as when carrying or storing the tool CHARGING/BATTERIES Charge battery only with the charger that is supplied with the tool Do not touch the contacts in the charger Do not expose tool/charger/battery to rain Never charge battery outdoors 4 Store tool/charger/battery in locations where temperature will not exceed 40C or drop below 0C Batteries will explode when disposed of in fire, so do not burn battery for any reason Do not use charger when damaged; take it to one of the officially registered SKIL Service Stations for a safety check Do not use charger when cord or plug is damaged; cord or plug should be replaced immediately at one of the officially registered SKIL Service Stations Do not use battery when damaged; it should be replaced immediately Do not disassemble charger or battery Do not attempt to recharge non-rechargeable batteries with the charger Explanation of symbols on charger/battery 3 Read the instruction manual before use 4 Only use the charger indoors 5 Double insulation (no earth wire required) 6 Fail-safe isolating transformer (the power source is electrically separated from the transformer output) 7 Automatic shut-off when charger gets too hot (thermic fuse blows and charger becomes useless) 8 Incorrect polarity of the charger connection could cause a hazard (only charge the battery with the charger supplied) 9 Do not dispose of the charger together with household waste material 0 Do not dispose of the battery together with household waste material 8 WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of the charger to the earth terminal of the plug If for any reason the old plug is cut off the cord of the charger, it must be disposed of safely and not left unattended USE Charging battery !- battery of new tools is not fully charged - connect charger to power source as illustrated - green light G will turn on indicating that the charger is ready for operation - insert battery into charger - red light H will turn on indicating that the battery is being charged - red light H will stay on as long as the battery is connected to the charger and the charger is in the wall socket !remove battery from charger after charging period has ended thereby lengthening the service life of the battery IMPORTANT: - while charging, the charger and the battery may become warm to touch; this is normal and does not indicate a problem - ensure that the outside surface of the battery is clean and dry before inserting into charger - do not charge at temperatures below 0 C and over 40 C; this will seriously damage the battery as well as the charger - do not remove battery from tool while it is running !a battery that is new or has not been used for a longer period does not develop its full capacity until after approximately 5 charging/discharging cycles - do not repeatedly recharge the battery after only a few minutes of operation; this may result in a reduction of operating time and battery efficiency - the nickel-cadmium battery must be kept separate from the natural environment and should not be disposed of as normal domestic waste (symbol 0 will remind you of this when the need for disposing occurs) !prior to disposal protect battery terminals with heavy tape to prevent short-circuit - if you anticipate long periods of non-use for the tool, it is best to unplug the charger from its power source On/off @ Changing direction of rotation # - when not properly set in left/right position, switch A 2 cannot be activated !change direction of rotation only when tool is at a complete standstill Changing bits $ - insert the bit as deep as possible in the chuck !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is < 70 dB(A) (standard deviation: 3 dB), and the vibration m/s2 (hand-arm method). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 335, EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est < 70 dB(A) (dviation standard: 3 dB), et la vibration m/s2 (mthode main-bras). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 335, EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes < 70 dB(A) (Standard- abweichung: 3 dB), und die Vibration m/s2 (Hand-Arm Methode). [. . . ] / EN 60 745 < 70 () ( : 3 ), i /2 ( ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. GR CE YMBATOT : EN 60 335, EN 60 745, EN 55 014, 2006/95/EK, 2004/108/EK, 98/37/EK ( 28. 12. 2009), 2006/42/EK ( 29. 12. 2009). Y / Y EN 60 745 < 70 dB(A) ( : 3 dB), m/s2 ( / ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 07 SKIL Europe BV A. [. . . ]