User manual SKIL 2455

[. . . ] Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 7 c) Do not expose power tools to rain or wet conditions. [. . . ] Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use an earth leakage circuit breaker. Use of an earth leakage circuit breaker reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR MIXERS · Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool · Never use the tool in or near an explosive atmosphere · Never mix combustible substances · Never reach with your hand or any other object into the mixing container during mixing · Wear protective gloves 4, a dust mask 5, close-fitting clothes and sturdy shoes · The noise level when working can exceed 85 dB(A); wear ear protection 6 · SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer · Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): · Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug · If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended · · · · · · 1 = LOW SPEED - high torque - for mixing high-density substances 2 = HIGH SPEED - lower torque - for mixing liquid substances Protection frame (1640) !- for protecting the tool - for guiding the tool - for putting aside the tool in a simple way - mount protection frame E before using the tool for the first time Operating the tool !ensure that the tool is switched off - mount mixing paddle G onto spindle F as illustrated @ - connect plug to power source - ensure the mixing container is securely positioned on the floor - dip the mixing paddle into the substance to be mixed - set wheel C 2 in position "1" - switch on the tool - gradually increase the mixing speed by turning wheel C 2 to the desired maximum speed (so that the substance will not splash around) !switch the tool off only when the mixing paddle is in the mixing container Electronic soft-start Ensures reaching the maximum speed smoothly without a sudden impact when tool is switched on Electronic constant speed Keeps the speed at a constant level as the load increases Electronic overload protection - reduces the mixing speed automatically in case the tool is overloaded for a longer period of time - release switch A 2 briefly for returning to normal working speed Holding and guiding the tool # !while working, always hold the tool at the grey-coloured grip area(s) !always hold the tool firmly with both hands MAINTENANCE / SERVICE · On/off 7 · Switch locking for continuous use 8 ! [. . . ] actuate the gear selector only when tool is switched off 8 USE · Always keep tool and cord clean (especially the ventilation slots) - always clean the mixer and functional parts after your mixing work - clean the tool with a dry, soft cloth (do not use cleaning agents or solvents) - clean ventilation slots H 2 regularly with a brush or compressed air !disconnect the plug before cleaning · AUTO-STOP Carbon brushes - this tool is equipped with carbon brushes which, when worn, prevent the motor from being damaged - when the tool stops unexpectedly, send it to your dealer or the nearest SKIL service-station for having the brushes replaced · If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools - send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. skilmasters. com) Mixeur INTRODUCTION 2455/1640 ENVIRONMENT · Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol $ will remind you of this when the need for disposing occurs · Ce mixeur électronique est destiné à mélanger facilement et simplement des substances · Différentes palettes permettent de mélanger une grande variété de substances (différents types de mélanges de ciment, colles de construction, peintures, composés de nivellement, mortier de finition et mortier sec, etc. ) · Le volume de mélange recommandé dépend du type et de l'état de la substance à mélanger, et du type de palette utilisée · Lisez et conservez ce manuel d'instruction 3 SPECIFICATIONS TECHNIQUES 1 ELEMENTS DE L'OUTIL 2 A B C D E F G H Interrupteur pour mise en marche/arrêt Bouton de blocage de l'interrupteur Molette de réglage de la vitesse maximum Commutateur de vitesse Cadre de protection (1640) Arbre Palette à mélanger Fentes de ventilation · We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 60745, EN 61000, EN 55014, in accordance with the provisions of the directives 2006/95/EC, 2004/108/EC, 2006/42/EC · Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL DECLARATION OF CONFORMITY SECURITE INSTRUCTIONS GENERALES DE SECURITE ATTENTION!Lisez tous les avertissements de sécurité et toutes les instructions. Ne pas suivre les avertissements et instructions peut entraîner un choc électrique, un incendie et/ou de graves blessures sur les personnes. [. . . ]