User manual SKIL 5064AA

[. . . ] c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Do not use any adapter plugs with earthed (grounded) power tools. [. . . ] b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 8 f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. ONLY): · Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug · If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE · Mounting saw blade 3 !disconnect the plug - take blade wrench A from storage B - push spindle-lock button C and hold it while you remove blade bolt D with blade wrench !push spindle-lock button C only when tool is at a standstill - release spindle-lock button C - remove flange E - open lower guard F with lever G and hold it while you mount saw blade with saw teeth and arrow printed on saw blade pointing in same direction as arrow on lower guard - release lower guard F - mount flange E !make sure that clamping surfaces H of flanges are perfectly clean and face the blade - push spindle-lock button C and hold it while you tighten blade bolt with blade wrench 1/8 turn past finger tight (ensures slippage of saw blade when it encounters excessive resistance thus reducing motor overload and saw kickback) - release spindle-lock button C · Adjusting cutting depth (0-64 mm) 4 - for an optimal quality cut the saw blade should not extend more than 3 mm below the workpiece - loosen lever J - raise/lower foot K until desired cutting depth is set on scale using indicator L - tighten lever J · Adjusting cutting angle (0-45°) 5 - loosen knob M - tilt tool until desired cutting angle is set on scale using indicator N · · · · - tighten knob M !when bevel cutting, cutting depth does not correspond with value on cutting depth scale 90° Cutting angle check 5 - adjust and tighten foot K to maximum cutting depth 4 - adjust and tighten cutting angle to 0° - check for a 90° angle between the blade and bottom of foot with a square Line-of-cut indicator P 6 - for guiding tool along desired line of cut marked on the workpiece - for a straight 0° cut or a 45° bevel cut use the indicator line concerned !the wide part of the foot should rest on the supported part of the workpiece !cutting width is determined by width of blade teeth and not by width of blade body ! [. . . ] La pénétration d'eau dans un outil électroportatif augmente le risque d'un choc électrique. d) N'utilisez pas le câble à d'autres fins que celles prévues, n'utilisez pas le câble pour porter l'outil ou pour l'accrocher ou encore pour le débrancher de la prise de courant. Maintenez le câble éloigné des sources de chaleur, des parties grasses, des bords tranchants ou des parties de l'outil en rotation. Un câble endommagé ou torsadé augmente le risque d'un choc électrique. [. . . ]