User manual SKIL 5246

[. . . ] ONLY): q Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug q If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended q q USE q q q q q q Changing saw blade 3 - open lower guard A by using lever B - change saw blade with saw teeth and arrow printed on saw blade pointing in same direction as arrow on lower guard A !make sure that clamping surfaces C of flanges are perfectly clean and face the blade - tighten blade bolt D with hex key 1/8 turn past finger tight (ensures slippage of saw blade when it encounters excessive resistance thus reducing motor overload and saw kickback) Adjusting cutting depth (0-46 mm) 4 - for an optimal quality cut the saw blade should not extend more than 3 mm below the workpiece - loosen lever E - raise/lower foot F until desired cutting depth is set on scale using indicator G - tighten lever E Readjusting clamping lever Clamping power of lever E can be readjusted - unscrew lever E and set it at at least 30° counterclockwise - screw tight lever E again Adjusting cutting angle (0-45°) 5 - loosen 2 knobs H 2 - tilt tool until desired cutting angle is set on scale using indicator J - tighten 2 knobs H 2 !when bevel cutting, cutting depth does not correspond with value on cutting depth scale 90° Cutting angle check 5 - adjust and tighten foot F to maximum cutting depth 4 - adjust and tighten cutting angle to 0° - check for 90° angle between the blade and bottom of foot with a square Kerf guide K 6 - protects saw blade from getting jammed in the workpiece - needs readjustment when min. /max. [. . . ] disconnect the plug before cleaning Clean saw blade immediately after use (especially from resin and glue) This SKIL product is guaranteed in accordance with statutory/country-specific regulations; damage due to normal wear and tear, overload or improper handling will be excluded from the guarantee In case of a complaint, send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. skileurope. com) Dispose of the tool by sorting tool, accessories and packaging for environment-friendly recycling (the plastic components are labeled for categorized recycling) APPLICATION ADVICE q q F q Always face the good side of the workpiece down to ensure minimum splintering Only use sharp saw blades of the correct type 8 - quality of cut improves by the number of teeth - carbide tipped blades stay sharp up to 30 times longer than ordinary blades Rip fence T 2 9 - for making exact cuts along a workpiece edge - can be inserted in either side of foot Adjusting rip fence - loosen knob U - adjust to desired cutting width by using rip fence scale (use line-of-cut indicator M 2 7 as 0-reference) - tighten knob U INTRODUCTION q Cet outil est conçu pour effectuer dans le bois des coupes droites longitudinales et transversales ainsi que des angles d'onglet jusqu'à 45°; muni de lames de scie correspondantes, il est capable de scier des matériaux non-ferroux, des matériaux de construction légers et des matières plastiques SPECIFICATIONS TECHNIQUES 1 SECURITE q Lire et conserver ce manuel d'instruction et les instructions de sécurité jointes 9 GB CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 50 144, EN 55 014, in accordance with the provisions of the directives 73/23/EEC, 89/336/EEC, 98/37/EEC. NOISE/VIBRATION Measured in accordance with EN 50 144 the sound pressure level of this tool is 100 dB(A), the sound power level 113 dB(A) and the vibration < 2. 5 m/s2 (hand-arm method). CE DÉCLARATION DE CONFORMITÉ Nous déclarons sous notre propre responsabilité que ce produit est en conformité avec les normes ou documents normalisés suivants: EN 50 144, EN 55 014, conforme aux réglementations 73/23/EEC, 89/336/EEC, 98/37/EEC. BRUIT/VIBRATION Mesuré selon EN 50 144 le niveau de la pression sonore de cet outil est 100 dB(A), le niveau de la puissance sonore 113 dB(A) et la vibration < 2, 5 m/s2 (méthode main-bras). CE KONFORMITÄTSERKLÄRUNG Wir erklären in alleiniger Verantwortung, daß dieses Produkt mit den folgenden Normen oder normativen Dokumenten übereinstimmt: EN 50 144, EN 55 014, gemäß den Bestimmungen der Richtlinien 73/23/EWG, 89/336/EWG, 98/37/EWG. GERÄUSCH/VIBRATION Gemessen gemäß EN 50 144 beträgt der Schalldruckpegel dieses Gerätes 100 dB(A), der Schalleistungspegel 113 dB(A) und die Vibration < 2, 5 m/s2 (Hand-Arm Methode). CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 50 144, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EEG, 89/336/EEG, 98/37/EEG. GELUID/VIBRATIE Gemeten volgens EN 50 144 bedraagt het geluidsdrukniveau van deze machine 100 dB(A), het geluidsvermogenniveau 113 dB(A) en de vibratie < 2, 5 m/s2 (hand-arm methode). CE KONFORMITETSFÖRKLARING Vi intygar och ansvarar för, att denna produkt överensstämmer med följande norm och dokument: EN 50 144, EN 55 014, enl. bestämmelser och riktlinjema 73/23/EWG, 89/336/EWG, 98/37/EWG. LJUD/VIBRATION Ljudtrycksnivån som uppmätts enligt EN 50 144 är på denna maskin 100 dB(A), ljudeffektnivån 113 dB(A) och vibration < 2, 5 m/s2 (hand-arm metod). CE KONFORMITETSERKLÆRING Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende normer eller normative dokumenter: EN 50 144, EN 55 014, i henhold til bestemmelserne i direktiverne 73/23/EØF, 89/336/EØF, 98/37/EØF. STØJ/VIBRATION Måles efter EN 50 144 er lydtrykniveau af dette værktøj 100 dB(A), lydeffektniveau 113 dB(A) og vibrationsniveauet < 2, 5 m/s2 (hånd-arm metoden). CE SAMSVARSERKLÆRING Vi erklærer at det er under vårt ansvar at dette produkt er i samsvar med følgende standarder eller standard- dokumenter: EN 50 144, EN 55 014, i samsvar med reguleringer 73/23/EWG, 89/336/EWG, 98/37/EWG. STØY/VIBRASJON Målt ifølge EN 50 144 er lydtrykknivået av dette verktøyet 100 dB(A), lydstyrkenivået 113 dB(A) og vibrasjonsnivået < 2, 5 m/s2 (hånd-arm metode). CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen standardien ja standardoimisasiakirjojen vaatimusten mukainen EN 50 144, EN 55 014, seuraavien sääntöjen mukaisesti 73/23/EWG, 89/336/EWG, 98/37/EWG. [. . . ] ZGOMOT/VIBRAØII Måsurat în conformitate cu EN 50 144 nivelul de presiune a sunetului generat de acest instrument este de 100 dB(A), nivelul de putere a sunetului 113 dB(A) iar nivelul vibraøiilor < 2, 5 m/s2 (metoda mînå - braø). CE KPA A COTETCTBE , : EN 50 144, EN 55 014, 73/23/EEC, 89/336/EEC, 98/37/EEC. /PA EN 50 144 100 dB(A), 113 dB(A), < 2, 5 m/s2 ( -). [. . . ]