User manual SKIL 5885

[. . . ] CIRCULAR SAW 5885 (F0155885. . ) GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 91 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 65 OR<J<NAL <fiLETME TAL<MATI . 136 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 08/08 ME77 2610398693 1 5885 2 EPTA 01/2003 2000 Watt 110 V = 1700 W 7, 9 kg 5000 /min RUBBER 90 45 235 mm MAX. 230 mm MIN. 85 mm 65 mm 30 mm 30 mm 3 G F C D E A H H B A 2 4 L 3 mm J K 5 FG H M N K M 3 6 A M M D E H A D E H K P NOT STANDARD INCLUDED 7 Q 4 8 9 34-35 mm SU V T R G F Q 0 5 ! @ F G X Q Q W # $ 6 GB Circular saw INTRODUCTION 5885 This tool is intended for lengthways and crossways cutting of wood with straight cuts as well as angle cuts to 45; with the appropriate saw blades also non-ferrous metals, light building materials and plastics can be cut Read and save this instruction manual 2 TECHNICAL SPECIFICATIONS 1 SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] - for making exact cuts along a workpiece edge - can be inserted in either side of foot Adjusting rip fence - loosen knob X - adjust to desired cutting width by using rip fence scale (use line-of-cut indicator Q as 0-reference) - tighten knob X Plunge cutting @ - set desired cutting depth - tilt tool forward with line-of-cut indicator Q lined up with desired line of cut marked on the workpiece - open lower guard F with lever G - just before blade enters workpiece, switch on tool and gradually lower back end of tool using front end of foot as hinge-point - gradually move tool downward as well as forward - as soon as blade enters the material, release lever G !the tool should run at full speed before the blade enters into the workpiece !never pull tool backwards Cutting large panels # - support panel close to the cut either on floor, table or workbench !set cutting depth so that you cut through panel and not through support - in case rip fence does not allow desired width of cut, clamp or nail straight piece of wood to workpiece as a guide, and use the left side of the foot against this guide Vibration level The vibration emission level stated at the back of this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned 10 - using the tool for different applications, or with different or poorly maintainted accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level !protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns SECURITE INSTRUCTIONS GENERALES DE SECURITE ATTENTION!Lisez tous les avertissements de scurit et toutes les instructions. Ne pas suivre les avertissements et instructions peut entraner un choc lectrique, un incendie et/ou de graves blessures sur les personnes. Conservez tous les avertissements et toutes les instructions pour pouvoir s'y reporter ultrieurement. La notion d'"outil lectroportatif" dans les avertissements se rapporte des outils lectriques raccords au secteur (avec cble de raccordement). 1) SECURITE DE LA ZONE DE TRAVAIL a) Maintenez l'endroit de travail propre et bien clair. Un lieu de travail en dsordre ou mal clair augmente le risque d'accidents. b) N'utilisez pas l'outil dans un environnement prsentant des risques d'explosion et o se trouvent des liquides, des gaz ou poussires inflammables. Les outils lectroportatifs gnrent des tincelles risquant d'enflammer les poussires ou les vapeurs. c) Tenez les enfants et autres personnes loigns durant l'utilisation de l'outil lectroportatif. En cas d'inattention vous risquez de perdre le contrle sur l'outil. 2) SECURITE RELATIVE AU SYSTEME ELECTRIQUE a) La fiche de secteur de l'outil lectroportatif doit tre approprie la prise de courant. N'utilisez pas de fiches d'adaptateur avec des outils avec mise la terre. Les fiches non modifies et les prises de courant appropries rduisent le risque de choc lectrique. b) Evitez le contact physique avec des surfaces mises la terre telles que tuyaux, radiateurs, fours et rfrigrateurs. Il y a un risque lev de choc lectrique au cas o votre corps serait reli la terre. c) N'exposez pas l'outil lectroportatif la pluie ou l'humidit. La pntration d'eau dans un outil lectroportatif augmente le risque d'un choc lectrique. [. . . ] Y / Y EN 60 745 94 dB(A) o 105 dB(A) ( : 3 dB), 2, 9 m/s2 ( / - K = 1, 5 m/s2). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 08 SKIL Europe BV A. Kloot 146 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 94 dB(A) iar nivelul de putere a sunetului 105 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 2, 9 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). [. . . ]