User manual SKIL 6222

[. . . ] CORDED DRILL/DRIVER 6222 (F0156222. . ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS NOTICE ORIGINALE ORIGINALBETRIEBSANLEITUNG ORIGINELE GEBRUIKSAANWIJZING BRUKSANVISNING I ORIGINAL ORIGINAL BRUGSANVISNING ORIGINAL DRIFTSINSTRUKS ALKUPERISET OHJEET MANUAL ORIGINAL MANUAL ORIGINAL ISTRUZIONI ORIGINALI EREDETI HASZNLATI UTASTS PVODNM NVODEM K POUZVN ORJNAL LETME TALMATI INSTRUKCJ ORYGINALN 6 8 11 14 17 20 22 25 28 31 34 37 40 42 45 RU UA GR RO BG SK HR 48 52 55 58 61 65 68 70 73 75 78 81 INSTRUCIUNI DE FOLOSIRE ORIGINALE PVODN NVOD NA POUZITIE ORIGINALNE UPUTE ZA RAD SRB ORIGINALNO UPUTSTVO ZA RAD SLO IZVIRNA NAVODILA EST ALGUPRANE KASUTUSJUHEND LV LT ORIINL LIETOSANAS PAMCBA ORIGINALI INSTRUKCIJA www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 03/09 2610399692 1 6222 0, 45 Amp 1, 2 kg EPTA 01/2003 0-300/850 8 mm 10mm 6 mm 6 2 E G F G C DB A 3 2 4 5 6 3 7 8 20 1 9 0 F 4 ! PHILLIPS POZIDRIV SLOTTED @ # $ % ^ 5 GB Corded drill/driver INTRODUCTION 6222 This tool is intended for drilling in wood, metal, ceramic and plastic as well as for screwdriving Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G Switch for on/off and speed control Switch for changing direction of rotation Keyless chuck Ring for torque control Lock-position (clutch) Gear selector Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. [. . . ] Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR DRILL/DRIVERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) Always keep the cord away from moving parts of the tool If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator) Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off 4 Speed control for smooth starting 5 Changing direction of rotation 6 - when not properly set in left/right position, switch A 2 cannot be activated !change direction of rotation only when tool is at a complete standstill Changing bits 7 - insert the bit as deep as possible in the chuck !do not use bits with a damaged shank Torque control (VariTorque) 8 - output torque will increase as clutch ring D is rotated from 1 to 20; position E will lock up the clutch to permit drilling or driving heavy duty work - when turning in a screw, first try VariTorque position 1 and increase until the desired depth has been reached Mechanical gear selection 9 - set selector F to desired speed !actuate the gear selector while tool is running slowly LOW - low speed - high torque - for screwdriving and drilling large diameters - for tapping thread 7 HIGH - high speed - lower torque - for drilling small diameters Holding and guiding the tool 0 !while working, always hold the tool at the greycoloured grip area(s) - keep ventilation slots G 2 uncovered - do not apply too much pressure on the tool; let the tool do the work for you ENVIRONMENT Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol ^ will remind you of this when the need for disposing occurs APPLICATION ADVICE Use the appropriate bits !only use sharp bits When drilling ferrous metals - pre-drill a smaller hole, when a large hole is required - lubricate drill bit occasionally with oil When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a hole in order to avoid cracking of the wood For an optimal use of the tool a steady pressure on the screw is required, especially while removing When screwdriving in hard wood one should pre-drill a hole Splinterfree drilling in wood @ Dustfree drilling in walls # Dustfree drilling in ceilings $ Drilling in tiles without skidding % For more tips see www. skileurope. com Vibration level The vibration emission level stated at the back of this instruction manual (indicated by an asterisk) has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with different or poorly maintainted accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 69 dB(A), the sound power level 80 dB(A) (standard deviation: 3 dB) and the vibration m/s2 (hand-arm method). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 69 dB(A), le niveau de la puissance sonore 80 dB(A) (dviation standard: 3 dB) et la vibration m/s2 (mthode main-bras). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 69 dB(A), der Schalleistungspegel 80 dB(A) (Standard- abweichung: 3 dB) und die Vibration m/s2 (Hand-Arm Methode). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 69 dB(A), het geluidsvermogen-niveau 80 dB(A) (standaard deviatie: 3 dB) en de vibratie m/s2 (hand-arm methode). Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. S CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 2006/95/EG, 2004/108/EG, 98/37/EG (till 28. 12. 2009), 2006/42/EG (from 29. 12. 2009). [. . . ] / EN 60 745 69 (), 80 () ( : 3 ) i /2 ( ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. UA GR CE : EN 60 745, EN 55 014, 2006/95/EK, 2004/108/EK, 98/37/EK ( 28. 12. 2009), 2006/42/EK ( 29. 12. 2009). / EN 60 745 69 dB(A), 80 dB ( : 3 dB) m/s2 ( / ). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 09 SKIL Europe BV A. [. . . ]