User manual SKIL 6692

[. . . ] Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. [. . . ] Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMER DRILLS Be aware of the forces that occur as a result of jamming (especially when drilling metals); always hold the tool firmly with both hands and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Read and save this instruction manual Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Be careful not to drill or drive into areas where electrical wires may be contacted If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool On/Off 3 Switch locking for continuous use 4 Speed control for smooth starting 5 Maximum speed control With wheel C the maximum speed can be adjusted from low to high (1-5) - switch on the tool - lock the switch - turn wheel C to select maximum speed For determining speed, table ( can be used as reference Changing direction of rotation 6 - when not properly set in left/right position, switch A cannot be activated !change direction of rotation only when tool is at a complete standstill Normal drilling/screwdriving versus hammer drilling 7 !select drilling function only when tool is switched off Changing bits 8 - insert the bit as deep as possible in the chuck !push spindle-lock button only when tool is at a complete standstill Adjusting drilling depth 9 Holding and guiding the tool 0 !always use auxiliary handle (can be adjusted as illustrated) - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you Dust filter system !always ensure that filter J is located in dust box K before use - only use the dust filter system when drilling in concrete, brick and stone !do not use the dust filter system when drilling in wood, metal and plastic - only use drill bits for stone with a maximum diameter of 12 mm and a maximum length of 200 mm - clean filter J and dust box K frequently Removing dust filter system @ !always close tube holder L when dust filter system is not being used Mounting dust filter system # 11 Use of dust filter system - the dust filter system with its telescopic action can be used in both horizontal and vertical working positions - dust box K !keeps hanging down straight in all side handle positions - ensure that the dust filter system firmly rests against the wall/floor/ceiling (which also ensures drilling at a straight 90 angle) $ !always pull switch A 2 to the maximum + select position 5 with wheel C 2 when using the dust filter system - remove drill bit from hole while tool is running to ensure dust suction performance - when dust filter system is not mounted, tool can be used again for drilling wood, metal and plastic Left- and right-hand use of side handle/dust filter system % Cleaning filter and dust box ^ In case of reduced dust suction performance, or when the collected dust has reached "MAX"-level M, filter J and dust box K should be cleaned - remove dust box K from dust filter system by pressing two red tabs N and slightly turning dust box towards you - remove filter J from dust box K and knock dust off of filter !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 100 dB(A) and the sound power level 111 dB(A) (standard deviation: 3 dB), and the vibration 11. 7 m/s2 (hand-arm method). CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 73/23/EC, 89/336/EC, 98/37/EC, 2002/96/EC. BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 100 dB(A) et le niveau de la puissance sonore 111 dB(A) (dviation standard: 3 dB), et la vibration 11, 7 m/s2 (mthode main-bras). CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 73/23/EG, 89/336/EG, 98/37/EG, 2002/96/EG. GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 100 dB(A) und der Schalleistungspegel 111 dB(A) (Standard- abweichung: 3 dB), und die Vibration 11, 7 m/s2 (Hand-Arm Methode). CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG, 2002/96/EG. GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 100 dB(A) en het geluidsvermogen-niveau 111 dB(A) (standaard deviatie: 3 dB), en de vibratie 11, 7 m/s2 (hand-arm methode). CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. [. . . ] BUKA/VIBRACIJE Mereno u skladu sa EN 60 745, nivo pritiska zvuka ovog alata iznosi 100 dB(A), a jaina zvuka 111 dB(A) (normalno odstupanje: 3 dB), a vibracija 11, 7 m/s2 (mereno metodom na aci-ruci). IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti: EN 60 745, EN 55 014, v skladu s predpisi navodil 73/23/EG, 89/336/EG, 98/37/EG, 2002/96/EG. HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 60 745 je raven zvonega pritiska za to orodje 100 dB(A) in jakosti zvoka 111 dB(A) (standarden odmik: 3 dB), in vibracija 11, 7 m/s2 (metoda `dlan-roka'). CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab jrgmistele standarditele vi normdokumentidele: EN 60 745, EN 55 014 vastavalt direktiivide 73/23/E, 89/336/E, 98/37/E, 2002/96/E nuetele. [. . . ]