User manual SKIL 7110

[. . . ] DELTA SANDER 7110 (F0157110. . ) 7115 (F0157115. . ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 58 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 41 OR<J<NAL <fiLETME TAL<MATI . 85 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 04/08 2610396816 1 7110 240 Watt 1, 2 kg EPTA 01/2003 7115 260 Watt 1, 2 kg EPTA 01/2003 2 1 C B 6 A D 2 3 4 5 A 3 6 7 7115 8 9 7115 4 0 7110 7115 AUTO 'CLIC' 3x ! ACCESSORIES SKIL Nr. 2x 2x 2610390730 2x 5 GB Delta sander INTRODUCTION 7110/7115 This tool is intended for dry sanding and finishing of wood, painted surfaces, plastic, metal and filler; it is particularly suitable for working on edged, narrow and other hard-to-reach places Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D Vacuum cleaner adapter On/off switch Sanding speed selection wheel Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) When sanding metal, sparks are generated; do not use vacuum cleaner and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn, torn or heavily clogged sanding sheets Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Mounting of sanding sheet 4 !the dust suction requires the use of perforated sanding sheets !perforation in sanding sheet should correspond with perforation in sanding foot !always use the tool with the total sanding surface covered with sanding paper - knock the dust out of the VELCRO material on the sanding plate before mounting the sanding sheet - mount VELCRO sanding sheet as illustrated Dust suction 5 - mount vacuum cleaner adaptor A as illustrated !do not use vacuum cleaner when sanding metal On/off switch - switch on/off the tool by pushing switch B 2 forward/backwards !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Speed control For optimal sanding results on different materials - with wheel C you can set the desired sanding speed - before starting a job, find the optimal speed and grit by testing out on spare material Holding and guiding the tool !while working, always hold the tool at the greycoloured grip area(s) 6 - guide the tool parallel to the working surface 7 !do not apply too much pressure on the tool; let the sanding surface do the work for you - do not tilt the tool in order to avoid unwanted sanding marks - keep ventilation slots D 2 uncovered Turnable foot (AUTO `CLIC') 7 (7115) - for changing front tip of sanding sheet/sanding foot when it is worn or damaged - for changing foot position depending on working surface (see: Application advice) - send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. skileurope. com) ENVIRONMENT Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol !Un lieu de travail en dsordre ou mal clair augmente le risque d'accidents. MAINTENANCE / SERVICE Always keep tool and cord clean (especially the ventilation slots D 2) - remove adhering sanding dust with a brush !disconnect the plug before cleaning If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools 8 GB CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 60 745, EN 55 014, in accordance with the provisions of the directives 2006/95/EC, 2004/108/EC, 98/37/EC (until Dec. NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 80 dB(A) and the sound power level 91 dB(A) (standard deviation: 3 dB), and the vibration 9. 2 m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 80 dB(A) et le niveau de la puissance sonore 91 dB(A) (dviation standard: 3 dB), et la vibration 9, 2 m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 80 dB(A) und der Schalleistungspegel 91 dB(A) (Standard- abweichung: 3 dB), und die Vibration 9, 2 m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). [. . . ] Y / Y EN 60 745 80 dB(A) o 91 dB(A) ( : 3 dB), 9, 2 m/s2 ( / - K = 1, 5 m/s2). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 08 SKIL Europe BV A. Kloot 90 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 80 dB(A) iar nivelul de putere a sunetului 91 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 9, 2 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). [. . . ]