User manual SKIL 7208AG

[. . . ] SANDER 7207 (F0157207. . ) 7208 (F0157208. . ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 60 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 43 OR<J<NAL <fiLETME TAL<MATI . 88 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 03/08 2610396117 1 7207 / 7208 100 Watt 1, 0 kg EPTA 01/2003 2 7207 7208 F E F G E B A C D B A C D NOT STANDARD INCLUDED NOT STANDARD INCLUDED 2 3 4 5 B A 6 3 7 B A 8 E 7207 E 7208 9 7208 0 F G 4 ! @ 5 #a #b $ % 6 GB Sander INTRODUCTION 7207/7208 This tool is intended for dry sanding and finishing of wood, painted surfaces, plastic and filler Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G Delta tip Button for changing foot plates Support plate Louvre attachment Dust bag (7207) / Dust box (7208) On/off switch Spot light (7208) SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug We recommend to use original SKIL-accessories as listed at the back of this instruction manual This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with When sanding metal, sparks are generated; do not use dustbag/dustbox and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn, torn or heavily clogged sanding sheets Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Mounting of sanding sheet 4 !the dust suction requires the use of perforated sanding sheets !perforation in sanding sheet should correspond with perforation in sanding foot !always use the tool with the total sanding surface covered with sanding paper - mount VELCRO sanding sheet as illustrated Mounting support plate 5 - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount support plate C as illustrated Mounting special sanding attachments 6 - mount desired sanding attachment to support plate C as illustrated - mount corresponding VELCRO sanding sheet to sanding attachment - 3 sanding positions Mounting "Louvre" attachment 7 - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount "Louvre" attachment as illustrated Dust suction 8 - mount dustbox E/dustbag E 8 - empty dustbox E/dustbag E regularly for optimal dust pick-up performance !do not use dustbox/dustbag when sanding metal On/off switch - switch on/off the tool by pushing switch F 2 forward/backwards !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Spot light 9 (7208) Spot light G automatically lights on when activating switch F Holding and guiding the tool 0 !while working, always hold the tool at the greycoloured grip area(s) - guide the tool parallel to the working surface !do not apply too much pressure on the tool; let the sanding surface do the work for you - do not tilt the tool in order to avoid unwanted sanding marks - keep the ventilation slots uncovered - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level !protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns MAINTENANCE / SERVICE Always keep tool and cord clean (especially the ventilation slots) - remove adhering sanding dust with a brush !disconnect the plug before cleaning If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools - send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. skileurope. com) APPLICATION ADVICE Use the tool with its standard foot plate for large working surfaces, corners and edges !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 71 dB(A) and the sound power level 82 dB(A) (standard deviation: 3 dB), and the vibration 14. 3 m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 71 dB(A) et le niveau de la puissance sonore 82 dB(A) (dviation standard: 3 dB), et la vibration 14, 3 m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 71 dB(A) und der Schalleistungspegel 82 dB(A) (Standard- abweichung: 3 dB), und die Vibration 14, 3 m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 71 dB(A) en het geluidsvermogen-niveau 82 dB(A) (standaard deviatie: 3 dB), en de vibratie 14, 3 m/s2 (hand-arm methode; onzekerheid K = 1, 5 m/s2). [. . . ] Kloot 94 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 71 dB(A) iar nivelul de putere a sunetului 82 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 14, 3 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). Documentaie tehnic la: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CE KPA A COTETCTBE , : EN 60 745, EN 55 014, 2006/95/EG, 2004/108/EG, 98/37/EG ( 28. 12. 2009), 2006/42/EG ( 29. 12. 2009). [. . . ]