User manual SKIL 7335AB

[. . . ] ORBITAL SANDER 7003 (F0157003. . ) 7335 (F0157335. . ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 53 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 37 OR<J<NAL <fiLETME TAL<MATI . 79 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 05/08 2610399150 1 7003 2 1, 3 kg EPTA 01/2003 C B 145 Watt A 7335 C 160 Watt 1, 3 kg EPTA 01/2003 3 4 2 5 A A 6 7 ACCESSORIES SKIL Nr. 2610384695 2610384697 2610390723 3 GB Orbital sander INTRODUCTION 7003/7335 This tool is intended for dry sanding and finishing of wood, painted surfaces, plastic and filler Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A Vacuum cleaner adapter B On/off switch C Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) Do not work materials containing asbestos (asbestos is considered carcinogenic) When sanding metal, sparks are generated; do not use vacuum cleaner and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn, torn or heavily clogged sanding sheets Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Mounting of sanding sheet 4 !the dust suction requires the use of perforated sanding sheets !perforation in sanding sheet should correspond with perforation in sanding foot !always use the tool with the total sanding surface covered with sanding paper Dust suction 5 - when using tool with/without vacuum cleaner, mount vacuum cleaner adaptor A as illustrated !do not use vacuum cleaner when sanding metal On/off switch - switch on/off the tool by pushing switch B 2 forward/backwards !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Holding and guiding the tool 6 !while working, always hold the tool at the greycoloured grip area(s) - guide the tool parallel to the working surface !do not apply too much pressure on the tool; let the sanding surface do the work for you - do not tilt the tool in order to avoid unwanted sanding marks - keep ventilation slots C 2 uncovered 5 APPLICATION ADVICE Move the tool in straight movements in line with the grain - for sanding bare wood surfaces - for extra fine finishing Never use the same sanding sheet for wood and metal Recommended sanding sheet grits: coarse - for removing paint;f or sanding of extremely rough wood medium - for sanding of rough or plain wood fine - for smoothing of wood; for finishing of bare wood; for smoothing surfaces with old paint Use different grit sizes when the working surface is rough: - start sanding with coarse or medium grit - finish with fine grit For more tips see www. skileurope. com Vibration level The vibration emission level stated at the back of this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with different or poorly maintainted accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 77 dB(A) and the sound power level 88 dB(A) (standard deviation: 3 dB), and the vibration 9. 3 m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 77 dB(A) et le niveau de la puissance sonore 88 dB(A) (dviation standard: 3 dB), et la vibration 9, 3 m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 77 dB(A) und der Schalleistungspegel 88 dB(A) (Standard- abweichung: 3 dB), und die Vibration 9, 3 m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 77 dB(A) en het geluidsvermogen-niveau 88 dB(A) (standaard deviatie: 3 dB), en de vibratie 9, 3 m/s2 (hand-arm methode; onzekerheid K = 1, 5 m/s2). [. . . ] Y / Y EN 60 745 77 dB(A) o 88 dB(A) ( : 3 dB), 9, 3 m/s2 ( / - K = 1, 5 m/s2). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 08 SKIL Europe BV A. Kloot 86 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 77 dB(A) iar nivelul de putere a sunetului 88 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 9, 3 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). [. . . ]